(3)
D00250 Petrolatum VV-P-236 (Optional)
(4)
D00633 Grease - BMS 3-33 (preferred)
(5)
D00013 Grease, MIL-G-23827 (optional)
(6)
G01395 Compound - Corrosion Inhibition, BMS 3-27, Mastinox 6856KReferences
(1)
AMM 07-11-01/201, Lifting Airplane for Maintenance
(2)
AMM 07-11-03/201, Jacking Airplane Axles
(3)
AMM 09-11-00/201, Towing
(4)
AMM 12-15-03/301, Wing Landing Gear Shock Strut
(5)
AMM 29-11-00/201, Main Hydraulic Supply System
(6)
AMM 32-00-30/201, Landing Gear Door Locks
(7)
AMM 32-61-22/201, Wiring Gear Truck Tilt Sensor
(8)
AIPC 32-11-02 Fig. 2Access
(1)
Location Zone 735 Wing Landing Gear, LH 745 Wing Landing Gear, RH
Prepare for the Procedure
S 498-100
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Install the ground locks in all landing gear (AMM 09-11-00/201).
S 498-101
WARNING: YOU MUST CAREFULLY DO THE STEPS BELOW TO INSTALL THE DOOR LOCKS
_______ ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).
S 498-102
(3)
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).
S 868-037
(4)
Release the pressure from the hydraulic system No. 4 (AMM 29-11-00/201).
(5)
Deflate the shock strut.
S 688-038
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-02
ALL ú ú 01A Page 820 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
WARNING: DO NOT REMOVE THE VALVE BODY UNLESS YOU DEFLATE THE SHOCK
_______ STRUT FULLY. THE AIR PRESSURE CAN BLOW THE VALVE OUT AND CAUSE INJURY TO PERSONS.
(a) Remove the air valve cap and loosen the outer nut no more than two turns.
NOTE: Fluid in the shock strut will have bubbles immediately
____ while you decrease the pressure to the ambient pressure. Deflate the shock strut slowly to prevent the leakage of fluid through the air valve.
(b) Put the tray below the flow fuse (drain plug).
S 688-039
(6)
After you decrease all the pressure on the shock strut, remove the drain plug and drain the fluid (AMM 32-11-02/301).
S 498-040
(7)
If it is available, install the retention tool for the shock strut of the landing gear.
S 018-041
CAUTION: FAILURE TO REMOVE THE TARGET BRACKET FOR THE SENSOR BEFORE THE
_______ SLING INSTALLATION CAN CAUSE DAMAGE TO THE BRACKET. AND IT CAN ALSO CAUSE DAMAGE TO THE POSITION INDICATION SYSTEM FOR THE LANDING GEAR.
(8)
If the retention tool for the shock strut is not available, remove the target bracket for the sensor (AMM 32-61-22/201).
(a)
Install the nylon sling to hold the shock strut in the compressed position.
S 588-043
(9)
Lift the airplane until the wheels are clear of the ground (AMM 07-11-01/201).
S 948-044
(10)
Put the axle jacks below each end of the truck beam (AMM 07-11-03/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-02
ALL ú ú 01A Page 821 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
G. Procedure
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(111)
