brace (9). 2) Apply grease around the outside diameter of the spherical bearing (15). 3) Put the spherical bearing (15) into the lower part of the drag brace (9). 4) Apply sealant BMS 5-95 around the surfaces and edges of the key washer (16).
(b)
AIRPLANES WITHOUT THE SMALLER SPHERICAL BEARING (15); Apply sealant BMS 5-95 class B-2 sealant into the lower bore of the drag brace (9), and around the flange area of the bore. 1) Install the spherical bearing (15) in the bore of the drag
brace (9).
(c)
Apply BMS 5-95 class B-2 sealant to both sides of the washer (38).
(d)
Install the washer (38).
(e)
Install the key washer (16).
1) Align the inner tang on the key washer with the groove in the spherical bearing.
(f)
Install the bearing nut (19).
1) Tighten the bearing nut (19) with hand.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-03
ALL ú ú 01 Page 408 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
2) Remove excess sealant.
3) Permit the sealant to cure for two hours.
4) Tighten the bearing nut (19) to 600 pound-inches (68 nm).
5) Loosen the bearing nut if it is necessary to align the
nearest castellation on the nut with a tang on the key washer (16). 6) Bend a tab on the key washer into a castellation on the bearing nut to lock the assembly.
S 644-020
(4)
Prepare the lubrication insert (11) for the trunnion bolt (12).
(a)
Examine the O-rings (10) for damage or deterioration. 1) Replace the O-rings if it is necessary.
(b)
Apply a thick layer of grease to the O-rings (10), the lubrication insert (11), and the inner diameter of the trunnion bolt (12).
(c)
Install the O-rings (10) on the lubrication insert (11).
(d)
Lubricate the lubrication insert again if it is necessary.
S 434-061
(5)
Install the lubrication insert (11) in the trunnion bolt (12).
(a)
Align the lockbolt holes on the lubrication insert with the lockbolt holes in the trunnion bolt.
S 644-021
(6)
Prepare the lubrication insert (20) for the drag brace pin (23).
(a)
Examine the O-rings (21) for damage or deterioration. 1) Replace the O-rings if it is necessary.
(b)
Apply a thick layer of grease to the O-rings (21), the lubrication insert (20), and the inner diameter of the drag brace pin (23).
(c)
Install the O-rings (21) on the lubrication insert (20).
(d)
Lubricate the lubrication insert (20) again if it is necessary.
S 434-062
(7)
Install the lubrication insert (20) in the drag brace pin (23).
(a)
Align the lockbolt holes on the lubrication insert with the lockbolt holes in the drag brace pin.
H.
Procedure
(1)
Install the stop fitting (5) at the top of the drag brace (9).
S 434-022
NOTE: The flanges of the stop fitting must be forward and aft.
____
S 644-023
(2) Lubricate the shanks and threads of the trunnion bolt (12), lockbolt (1), and antirotation bolt (6) with grease.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-03
ALL ú ú 01 Page 409 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(3) S 644-048Lubricate the surfaces of the washers (2, 4, and 7).
(4) S 494-024Install the thread protector on the trunnion bolt (12).
(5) S 424-025Connect the top end of the drag brace (9) to the trunnion fork. (a) Lift the drag brace (9) into the correct position with the hoist. (b) Install the trunnion bolt (12) with the lubrication insert (11) to connect the top of the drag brace to the trunnion fork.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(123)
