S 434-046
 (25)
 Install the hydraulic lines on the shock strut.

 (a)  
Remove all caps and plugs from the hydraulic lines and the fittings.

 (b)  
Connect all disconnected connections.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01 Page 413 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-038
 (26)
 Attach the wire harness and the junction box to the shock strut.

 (a)  
Do a visual check of the locknuts and the safety wires.

 (b)  
Tighten the locknuts which are loose.

 (c)  
Replace all safety wires which have damage.

 S 434-039
 (27)
 If you used an assembly stand, move the landing gear to a transportation dolly.

 (a)  
Attach the landing gear to the transportation dolly.

 S 434-040
 (28)
 Install the wing landing gear on the airplane (AMM 32-11-01/401).

 S 434-041

 (29)
 Install the outboard door fitting on the shock strut
 (AMM 32-11-28/401).

 S 434-042

 (30)
 Install the drag brace (AMM 32-11-03/401).

 H.
Put the Airplane in its Usual Condition

 S 094-042
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).

 S 094-043

 (2)  
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01 Page 414 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 714-044
 (3) Do an system test of the wing landing gear (AMM 32-32-00/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01 Page 415 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING LANDING GEAR SHOCK STRUT - REPAIRS
_______________________________________
 1.  General_______
 A.  This procedure has three tasks:
 (1)  
The replacement of the inner cylinder seals with the spare seals (lift the airplane with the jacks or lower the gear on a pit)

 (2)  
The replacement of the inner cylinder seals and the spare seals

 (3)  
The replacement of the inner cylinder seals with the spare seals. (without the use of the airplane jack)

 B.  
For more seal replacements, disconnect the truck beam from the inner cylinder yoke and move the seals through the yoke. You put MIL-H-5606 fluid on the edge of the replacement seals which have four marks.

 TASK 32-11-02-368-115
 2.  Inner Cylinder Seals Replacement with Spare Seals (Fig. 802)____________________________________________________________
 A.  General
 (1)  
This task lifts the airplane with jacks or lowers the airplane over a pit to replace the seals.

 (2)  
You can replace the lower cylinder seals for the seal leaks in the shock strut. You can find the spare seals in the grooves of the lower bearing. You can use the spare seals for the first and second seal replacement. The removal of the inner cylinder or other major components for these replacements is not necessary.

 B.  
Special Tools and Equipment

 (1)  
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 1(102)