(4)  
4PRE65B00161-1 - Wing Gear Side Strut Upper Spindle Protective Equipment (Thread Protector)

 B.
Standard Tools and Equipment

 (1)  
Hoist - Standard ~..................................................... | vertical range: | ground level to 19 feet | ....................................................... | maximum load: | 350 pounds | ....................................................... | load at maximum extension:| 205 pounds | 2...........................….........................1

 C.
Consumable Material

 (1)  
D00633 Grease - BMS 3-33 (preferred)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-05
 ALL  ú ú 01 Page 405 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
D00013 Grease - MIL-G-23827 (optional)

 D.
References

 (1)  
AMM 07-11-01/201, Jacking Airplane

 (2)  
AMM 09-11-00/201, Towing

 (3)  
AMM 12-15-03/301, Servicing - Wing Gear Shock Strut

 (4)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (5)  
AMM 32-00-30/201, Landing Gear Door Locks

 (6)  
AMM 32-11-05/601, Wing Gear Upper Side Strut Spindle

 (7)  
AMM 32-32-16/401, Wing Gear Downlock Bungee

 (8)  
AIPC 32-11-05 Fig. 1

 (9)  
AIPC 32-32-16 Fig. 2

 (10)
 AIPC 32-32-26 Fig. 2

 E.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 F.
Prepare for the Procedure

 S 224-020
 (1)  
Examine the fit of the side strut bolt where the side strut attaches to the spindle (AMM 32-11-05/601).

 S 644-021

 (2)  
Prepare the lubrication insert for installation into the side strut bolt.

 (a)  
Examine the O-rings for deterioration or damage. 1) If it is necessary, replace the O-rings.

 (b)  
Apply a large quantity of grease to the O-rings and the lubrication insert.

 (c)  
Apply a large quantity of grease to the inner surface of the side strut bolt.

 (d)  
Put the O-rings on the lubrication insert.

 (e)  
If it is necessary, lubricate the lubrication insert again.

 S 434-045
 (3)  
Install the lubrication insert into the side strut bolt.

 (a)  
Align the lockbolt holes in the lubrication insert with the holes in the side strut bolt.

 G.
Procedure

 S 644-022
 (1)  
Apply a thin layer of grease to the surfaces of the spindle, the spline washer, and the spindle nut.

 S 424-023

 (2)  
Install the spindle in the support structure with the thread protector.

 (3)  
Remove the thread protector.

 S 094-024
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-05
 ALL  ú ú 01 Page 406 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 434-025

 (4)  Install the spline washer with the spindle nut.
 (a) Tighten the nut with your hands.
 S 644-026
 (5)  Apply a layer of grease to the threads of the side strut bolt.
 S 644-046
 (6)  Apply a layer of grease to the surfaces of the tang washer.
 S 424-027
 (7)  Connect the spindle to the top end of the upper side strut.
 (a) Align the upper side strut with the spindle.
 (b) Put the swivel bracket in the correct position for installation
 of the side strut bolt.
 (c) Install the side strut bolt with the lubrication insert.
 (d) Install the tang washer.
 (e) Install the special nut.
 1) Tighten the nut 480 to 600 pound-inches.
 2) Loosen the nut to align the nearest castellation of the nut
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(135)