曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

A
747-400 MAINTENANCE MANUAL
 (d)  Make sure that these indications occur when the software loading is done: 1) The COMP indicator is on. 2) The RDY indicator is off. 3) The PROG indicator is off.
 NOTE: Approximate LRU loading times are:
____ ~........................................... | LRU | APPROXIMATE LOADING TIMES | ............................................. | DU | 12-16 minutes | ............................................. | EIU | 8-10 minutes | 2...........…...............................1
 (e)  Push the eject button and remove the diskette from the disk drive.
 S 472-009
 (2)  
Do the IDS Software Installation task for the other IDS LRUs, if it is necessary.

 S 862-039

 (3)  
If you loaded software in one, two or three EIUs,

 (a)
Open and then close the applicable EIU circuit breaker:

 1)  P7, Overhead Circuit Breaker Panel
 a) 7F9, EIU L
 b) 7F10, EIU C
 c) 7F15, EIU R

 (b)  
Stop a minimum of 12 seconds to let the EIU to warm-up.

 

 S 472-040
 (4)  If you loaded software in all three EIU's,
 (a)  Open this circuit breaker:
 1)  P415, Power Distribution Center - Right Panel a) 415L39, CMC RIGHT
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-61-10
 ALL  ú ú 05 Page 203 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (b) (c)  Open and then close this circuit breaker: 1) P414, Power Distribution Center - Left Panel a) 414L8, CMC LEFTStop until the <CMC prompt appears on the CDU main menu.
 NOTE:____ It can take up to 5 minutes for the <CMC prompt to appear.
 (d)  Push the LSK (line select key) adjacent to the <CMC prompt to show the CMC menu.
 NOTE:____ If the CMC menu is not shown, push the <RETURN LSK, if it is necessary, until you see the menu.
 (e) (f) (g) (h) (i) (j) (k) (l)  Push the <OTHER FUNCTIONS LSK to show the OTHER FUNCTIONS menu.Push the <CONFIGURATION LSK to show the CONFIGURATION menu.Push the <CENTRAL MAINTENANCE LSK to show the CENTRAL MAINTENANCE menu.Push the <CMC-L LSK.Verify the correct EIU S/W P/N is shown next to LSK 5L.Open this circuit breaker: 1) P414, Power Distribution Center - Left Panel a) 414L8, CMC LEFTClose this circuit breaker: 1) P415, Power Distribution Center - Right Panel a) 415L39, CMC RIGHTStop until the <CMC prompt appears on the CDU main menu.
 NOTE:____ It can take up to 5 minutes for the <CMC prompt to appear.
 (m)  Push the LSK (line select key) adjacent to the <CMC prompt to show the CMC menu.
 NOTE:____ If the CMC menu is not shown, push the <RETURN LSK, if it is necessary, until you see the menu.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-61-10
 ALL  ú ú 05 Page 204 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (n)  
Push the <OTHER FUNCTIONS LSK to show the OTHER FUNCTIONS menu.

 (o)  
Push the <CONFIGURATION LSK to show the CONFIGURATION menu.

 (p)  
Push the <CENTRAL MAINTENANCE LSK to show the CENTRAL
 MAINTENANCE menu.

 (q)  
Push the <CMC-R LSK.

 (r)  
Verify the correct EIU S/W P/N is shown next to LSK 5L.

 (s)  
Close this circuit breaker:

 1)  P414, Power Distribution Center - Left Panel a) 414L8, CMC LEFT
 S 752-010
 (5)  Do a check of the software installation:
 (a)  
Set the GND TESTS switch on the P461 panel to the ENABLE position.

 (b)  
Set the INBD CRT and LWR CRT switches on the two display transfer modules to the NORM position.

 (c)  
Set the EIU SEL switch on the EICAS control panel/FMC switch to the C position.

 (d)  
Set the EIU switch on the captain's source select module to the L position.

 (e)  
Set the EIU switch on the first officer's source select module to the R position. 1) Make sure the outboard IDUs show the PFD format. 2) Make sure the inboard IDUs show the ND format. 3) Make sure the upper EICAS IDU shows the primary engine
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 2(167)