GLARESHIELD
FWD
PANEL
L OR R REMOTE LIGHT SENSOR, M3488 OR M3489
OUTBD-CRT-INBD
INBD-CRT-OUTBD
CAPT EFIS BRIGHTNESS CONTROLS, F/O EFIS BRIGHTNESS CONTROLS,
R2267 AND R2268 R2270 AND R2269
Integrated Display System - Component Location (Details from Sht 1)
Figure 102 (Sheet 7)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-61-00
ALL ú ú 01 Page 108 ú Oct 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 FAULT ISOLATION/MAINT MANUAL
MOUNTING
SCREW
PHOTODIODE
CAPTAIN'S EFIS BRIGHTNESS CONTROLS, FIRST OFFICER'S EFIS BRIGHTNESS CONTROLS, R2267 AND R2268 R2270 AND R2269
Integrated Display System - Component Location (Details from Sht 1)
Figure 102 (Sheet 8)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-61-00
ALL ú ú 04 Page 109 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
K01096
A
747-400 MAINTENANCE MANUAL
INTEGRATED DISPLAY SYSTEM - MAINTENANCE PRACTICES
_________________________________________________
1. General_______
NOTE: Transition through certain MACH numbers will cause large changes
____ in the minimun speed display on the PFD. These transitions may also cause the CAPT's and the F/O's minimun speed display to indicate different speeds.
The frequency of an unpowered APU or external power source may shown as 122 Hertz (rather than 0 Hertz) on the electrical maintenance page.
Decision speed (V1) and rotation speed (VR) may disappear from the PFD. If this occurs, select the onside EIU switch on the source select module to an alternate EIU position to restore the display.
If blooming is observed in any IDU, replace the affected IDU. Blooming is described as a glow on one side of the IDU. The IDUs continuosly conduct an off screen beam test that directs the beam outside the normal view area and turns the beam on. The commanded position of the beam display area and display orbiting are close enough to the IDU tolerance, therefore the beam test glow may become visible in some units.
A. This procedure has these tasks:
(1)
Obtaining airplane system information using the Engine Indicating and Crew Alerting (EICAS) portion of the Integrated Display System (IDS).
(2)
Erasing latched status level EICAS messages.
(3)
Cancelling, recalling and/or erasing EICAS engine parameter exceedances.
(4)
Manual Snapshot Recording
(5)
Snapshot Display
(6)
Snapshot Erasure
(7)
Snapshot Memory Reset
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-61-00
ALL ú ú 02 Page 201 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(8) ACARS Report of a Maintenance Page - Second Page is Empty
B. Each task is an independent task and can be performed individually, as required.
C. EICAS Information
(1)
The EICAS performs the functions of engine indicating and crew alerting. The EICAS displays data transmitted from many systems. In addition to indicating engine data, the EICAS displays and/or stores information related to airplane maintenance, dispatch condition, and system configuration.
(2)
There are three configurations of the EICAS display format. These configurations are: normal, non-normal, and degraded.
(a)
Normal configuration 1) Two EICAS capable DUs available. 2) Secondary engine parameter exceedances (oil pressure, oil
temperature, oil quantity, vibration) do not exist.
(b)
Non-normal configuration 1) Two EICAS capable DUs available 2) Secondary engine parameter exceedances exist.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 2(113)
