(2)  
AMM 20-41-02/201, Electrostatic Discharge Sensitive Devices

 (3)  
AMM 28-31-17/501, Fuel Jettison Single Point Sensor Control Card

 (4)  
AIPC 28-15-60, Fig. 1

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-17
 ALL  ú ú 01 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

ELECTROSTATIC GROUND JACK
FUEL SYSTEM CARD FILE
SEE A
A
A
FUEL SYSTEM CARD FILE A
SPS CONTROL CARD A4 A-AFuel Jettison Single Point Sensor Control Card Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-17
 ALL  ú ú 01 Page 402 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (5)  
SSM 28-31-05, SSM 28-44-01

 (6)  
WDM 28-31-31, WDM 28-44-11, WDM 28-44-12

 B.
Access

 (1)  
Location Zone
 115 Area Between Nose Gear Well and Fuselage, Left

 C.
Procedure

 S 844-010
 CAUTION: DO NOT TOUCH THE CONTROL CARD BEFORE YOU DO THE PROCEDURE FOR
_______ DEVICES THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE DAMAGE TO THE CONTROL CARD.
 (1)  
Do the procedure for devices that are sensitive to electrostatic discharge (AMM 20-41-02/201).

 S 424-009

 (2)  
Install the control card in the M7852 fuel system card file at location A4 (AMM 20-11-22/401).

 S 864-005

 (3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6, Main Power Distribution Panel
 1) 6C17, FUEL JTSN CONT B
 2) 6D17, FUEL JTSN CONT A

 (4)
Do the single point sensor (SPS) BIT test (AMM 28-31-17/501).

 S 744-006
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-17
 ALL  ú ú 01 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 FUEL JETTISON SINGLE POINT SENSOR CONTROL CARD - ADJUSTMENT/TEST
________________________________________________________________
 1.  General_______
 A.  This procedure contains an operational test of the single-point sensor (SPS) components for the fuel jettison system. The operational test uses the built in test (BIT) in the SPS control card. You can do the BIT test at the SPS control card or do the CMCS ground test, <SNGL PT SNSR CARD. This test makes sure that the SPS system components (single point sensors, control card, and wiring between the card and sensors) are OK.
 B.  You cannot adjust the single-point sensors or the control cards.
 C.  The SPS fuel jettison control card (JETT M2 M3 SPS) is installed in the fuel system card file, M7852, in slot A4.
 (1)  
Access to the card file is in the left crawlway adjacent to the wheel well for the nose gear.

 D.  
The single point sensors are found in the No. 2 and 3 main tanks and are located at the fuel level for 3000 U.S. gallons (11,350 liters).

 NOTE: The 3K GAL. fuel level is set for an in-flight airplane.
____
 (1)  On the ground the fuel quantity that is necessary to cover the single point sensors with fuel will change with different fuel densities or airplane attitudes. These fuel quantities will make sure the SPS senors are always "dry" or "wet" at all nominal airplane ground attitudes and fuel densities:
 JETT M2 M3 SPS "DRY" inputs, maximum of 2850 U.S. gallons.
 JETT M2 M3 SPS "WET" inputs, minimum of 3750 U.S. gallons.

 or
 JETT M2 M3 SPS "DRY" inputs, maximum of 10,790 liters.
 JETT M2 M3 SPS "WET" inputs, minimum of 14,200 liters.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(81)