(a)  
On the main power distribution panel, P6: 1) 6D5, FUEL QTY 1 2) 6D6, FUEL QTY 2 3) 6E17, CTR R & MAIN 2 JTSN VLV 4) 6F17, CTR L & MAIN 3 JTSN VLV

 (b)  
On the DC power distribution panel, P180: 1) 180C25, FUELING LTS PANEL 2) 180C26, FUELING LTS RECP 3) 180E3, FUEL OVRD/JTSN PMP CONT FWD 2&3 4) 180E18, FUEL OVRD/JTSN PMP CONT AFT 2&3 5) 180H17, FUEL SYS EICAS INTFC CONT 6) 180M9, FUELING PWR - HOT BAT 7) 180M8, FUELING VALVE 2

 (c)  
On the left power distribution center, P414: 1) 414C2, FUEL OVRD/JTSN PUMP FWD 2 2) 414C5, FUEL OVRD/JTSN PUMP FWD 3 3) 414F17, FUELING VALVE 4) 414F22, FUELING PWR

 (d)  
On the right power distribution center, P415: 1) 415A38, FUEL OVRD/JTSN PUMP AFT 2

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-00
 ALL  ú ú 07 Page 532 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2) 415B38, FUEL OVRD/JTSN PUMP AFT 3
 3) 415M14, FUEL OVERFILL CONT

 S 865-220
 (9)  Make sure the ground lockpins for the landing gear are installed.
 S 495-199
 WARNING: USE THE PROCEDURE IN AMM 32-00-30/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (10) Install the wing and body gear door locks (AMM 32-00-30/201).
 S 495-213
 WARNING: REFER TO AMM 27-81-00/201 FOR LOCK INSTALLATION PROCEDURE.
_______ FLAPS WILL RETRACT IN 7 SECONDS. INSTALL LOCKS TO PREVENT INJURY FROM INADVERTENT OPERATION OF FLAPS.
 (11)
 Install the locks on all the extended leading edge flaps (AMM 27-81-00/201).

 S 865-252

 (12)
 Have a person go out to the pressure refuel station (left wing) and do these steps:

 (a)  
Fully open the access door, 521CB, for the refuel control panel. 1) Let the door guide engage the detent.

 (b)  
Make sure the panel floodlights come on.

 (c)  
Make sure the fuel quantity indicators come on and give the correct fuel quantity.

 (d)  
Put the POWER switch on the refuel control panel in the NORM or BATT position.

 S 865-248
 (13) Make sure the levers for the refuel receptacles (left and right wing) are in the CLOSED position.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-00
 ALL  ú ú 15 Page 533 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-217
 (14)
 Make sure the manual defuel valve handles (for the left and right wing) are in the CLOSED position.

 F.  
Fuel Transfer Test - Jettison Transfer Valves - Valves Closed

 S 715-243
 (1)  
Do this task: Fuel Jettison Transfer Valve - Ground Test
 (AMM 28-31-00/501).

 (a)  
If the ground test shows a FAIL indication, do the corrective action for any CMCS messages that show during the test.

 S 715-187
 (2)  
Have a person go out to the refuel control panel, P42.

 (a)  
Put this switch on the P42 panel to the OPEN position: 1) MAIN 1 refuel valve switch.

 S 715-251
 (3)  
Do these steps to make sure the four jettison transfer valves are in the closed position:

 (a)  
Put these override/jettison pump switches on the fuel manangement control module, M154 (pilots' overhead panel, P5) to the ON position: 1) OVRD 2 FWD 2) OVRD 2 AFT 3) OVRD 3 FWD 4) OVRD 3 AFT

 (b)  
Look at the fuel synoptic. 1) Wait for two minute. 2) Make sure the fuel quantity in the No. 1 main tank does not

 increase.
 3)  If the fuel quantity in the No. 1 main tank does not increase, all of the jettison transfer valves are in the closed position.
 (c)  Put these override/jettison pump switches on the fuel manangement control module, M154, to the off position: 1) OVRD 2 FWD
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(14)