S 655-195
(4)
Make sure the fuel tanks contain these fuel quantities:
NOTE: At different pitch and roll attitudes the fuel quantity
____ that is necessary to cover the pump fuel inlets will change. See the pump fuel inlet graphs in this procedure: Test of the Motor/Impeller Unit Installation (AMM 28-31-01/401).
NOTE: The inboard main tanks, No. 2 and No. 3 must not be full
____ (at VTO). If a fuel tank is full (at VTO) the refuel valve(s) for that tank will not operate electrically.
(a) The No. 2 and No. 3 reserve tanks and the No. 1 and No. 4 outboard main tanks can contain some quantity of fuel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-31-00
ALL ú ú 14 Page 544 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) No. 2 and No. 3 main tanks - minimum of 12,500 lbs (5700 kgs)
of fuel.
NOTE:____ At different pitch and roll attitudes, this fuel
quantity can be less.
(c) Center wing tank - maximum of 60,000 lbs (27,200 kgs) and a
minimum of 15,000 lbs (6800 kgs) of fuel.
NOTE:____ At different pitch and roll attitudes, this fuel
quantity can be less.
S 655-206
(5)
If the fuel quantity is not sufficient, refuel the tank(s) (AMM 12-11-01/301) or move fuel from a different tank (AMM 28-26-00/201) if it is necessary.
S 865-207
(6)
Make sure that all the FUEL CONTROL switches on the control stand are set to the CUTOFF position.
S 865-126
(7)
Make sure all of the override/jettison pump switches on the fuel management control module, (P5 pilots' overhead panel) are off (the white ON indication light in each pump switch does not show).
S 865-199
(8)
Make sure all of the boost pump switches on the fuel management control module, (P5 pilots' overhead panel) are off (the white ON indication light in each pump switch does not show).
S 865-208
(9)
Make sure all of the crossfeed valve switches on the fuel management control module (P5 pilots' overhead panel) are off (the white flowbar indication light in each crossfeed valve switch does not show).
S 865-246
(10)
Make sure that the FUEL JETTISON control selector switch on the fuel jettison module, (P5 pilots' overhead panel) is in the OFF position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-31-00
ALL ú ú 12 Page 545 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-134
WARNING: MAKE SURE YOU DO THE STEPS TO REMOVE POWER FROM THE JETTISON
_______ NOZZLE VALVE ACTUATORS. IF THE POWER TO THE JETTISON NOZZLE VALVE ACTUATORS IS NOT REMOVED, THE NOZZLE VALVES WILL OPEN. WITH THE NOZZLE VALVES OPEN, FUEL PRESSURIZED BY THE JETTISON PUMPS CAN FLOW FROM THE WINGTIPS AT THE JETTISON NOZZLES. A FUEL LEAK FROM THE JETTISON NOZZLES CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(11)
Do these steps to make sure the power is removed from the jettison nozzle valve actuators (SSM 28-31-03, WDM 28-31-13).
(a)
Make sure these circuit breakers are closed:
1) On the main power distribution panel, P6: a) 6C18, JTSN NOZZLE VLV CONT R b) 6D18, JTSN NOZZLE VLV CONT L
(b)
Make sure the FUEL JETTISON L-NOZZLE and NOZZLE-R switches on the fuel jettison module (P5 pilots' overhead panel) are in the off position (the white ON indication light in each switch does not show).
(c)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
1) On the P6 panel: a) 6C18, JTSN NOZZLE VLV CONT R b) 6D18, JTSN NOZZLE VLV CONT L
(d)
Remove these access doors to get to the actuators for the jettison nozzle valves: 1) 556BA Wingtip Dry Bay Access Door 2) 656BA Wingtip Dry Bay Access Door
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(19)
