C.
Prepare the Airplane for FQIS Wire Bundle Removal

 S 654-172
 (1)  
Defuel the airplane (AMM 28-26-00/201).

 S 864-003

 (2)  
To replace the wire bundle to the outboard or reserve tank, put the airplane in the wing jig position.

 NOTE: The wing jig position will prevent a possible bolt
____ mis-alignment problem when the inspar removable ribs are removed and installed (AMM 57-12-01/401).
 S 864-002
 WARNING:_______OBEY THE PURGING AND FUEL TANK ENTRY PRECAUTIONS. FAILURE TO OBEY THE PRECAUTIONS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (3)  
Purge and prepare to go into the applicable fuel tank(s)
 (AMM 28-11-00/201).

 S 024-004

 (4)
Remove all the applicable wing main and reserve tank access panels.

 D.
Procedure

 S 034-013
 (1)  Disconnect the applicable wire bundle connector from out of the fuel tank.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-41-09
 ALL  ú ú 01 Page 412 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-014
 (2)  Remove the jamnut from the out of the fuel tank that attaches the tank wire bundle connector to the spar.
 S 944-005
 WARNING:_______OBEY THE FUEL TANK ENTRY PRECAUTIONS. FAILURE TO OBEY THE FUEL TANK ENTRY PRECAUTIONS COULD CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (3)  
Obey the fuel tank entry precautions (AMM 28-11-00/201).

 S 944-006

 (4)  
Go into the fuel tank.

 S 034-007

 (5)  
Disconnect the wire terminals from the terminal block of applicable tank units and compensator or densitometer (main tank only).

 S 034-008

 (6)  
Loosen the strain relief clamps at the terminal blocks and remove the wires from the clamps.

 S 034-009

 (7)  
Remove all the clamps that attach the wire bundle to the fuel tank structures.

 S 014-010

 (8)  
If a reserve or outboard tank wire bundle is replaced, remove the inspar removable ribs at WS 1056 and WS 1168 (AMM 57-12-01/401).

 S 034-011

 (9)  
Remove electrical wire bundle seals where used on tank dividers and tank baffles (AMM 51-31-01/201).

 S 034-012

 (10)
 If the wire bundle goes through more than one tank, do these steps:

 (a)  
Pull the loose end of the wire bundle back through the tank divider seal area into the adjacent inner tank.

 (b)  
Remove the wire bundle clamps in the adjacent tank.

 (c)  
If it is necessary, do this procedure again until all the wire bundle clamps are removed thru the inboard tank spar connector.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-41-09
 ALL  ú ú 01 Page 413 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-015
 (11)
 Remove the connector from the spar.

 S 024-017

 (12)
 Remove the FQIS wire bundle from the tank.

 S 034-016

 (13)
 Discard the connector O-ring.

 S 864-018

 (14)
 Keep the airplane in the prepared for fuel tank entry configuration to do the installation task.

 TASK 28-41-09-404-019
 3.  FQIS Wire Bundle in the Main or Reserve Tank Installation (Fig. 402)_________________________________________________________
 A. Equipment
 (1)
Bonding Meter (SWPM 20-20-00) Approved for use in fuel vapor areas.

 B.
Consumable Materials

 (1)
A00249 Sealant - BMS 5-26 Type II Class B

 C.
References

 (1)
AMM 24-22-00/201, Manual Control

 (2)
AMM 28-11-00/201, Fuel Tanks

 (3)
AMM 28-41-00/501, Fuel Quantity Indicating System

 (4)
AMM 28-41-01/401, Fuel Quantity Tank Unit
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(125)