28-31-13
 ALL  ú ú 01 Page 402 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400 MAINTENANCE MANUAL
ADAPTER OF THE FUEL JETTISON TRANSFER VALVE
SEE A
INDEX ARROWS 
VALVE BODY 
INDEX PLATE 
MOUNTING SCREW (3 LOCATIONS)  B 
ACTUATOR  SEE VALVE BODY ADAPTER PLATE  B 

PACKING ADAPTER SHAFT
REAR 
SPAR  WASHER 
(4 LOCATIONS) 
FWD  BOLT 
(4 LOCATIONS)

ADAPTER OF THE FUEL JETTISON TRANSFER VALVE
A
Fuel Jettison Transfer Valve Adapter

Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-13
 ALL  ú ú 01 Page 403 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 B. Consumable Materials
 (1)  
A00247 Sealant - Corrosion Protection, BMS 5-95

 (2)  
C00064 Coating - Alodine 600 Chemical conversion coating for aluminum or aluminum alloy, (MIL-C-5541).

 (3)  
C00307 Corrosion Resistant Finish - BMS 10-20 Type II

 (4)  
D00128 Petrolatum - Technical, VV-P-236

 C.
Parts

 ~.............................................................................. | MM | | IPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Shaft - Adapter | 28-31-04 | 01 | 45 | 2......…........…...................................…..........….....….........1
 D. References
 (1)  
AIPC 28-31-04, Fig. 1

 (2)  
AMM 12-11-01/301, Fuel Service

 (3)  
AMM 28-00-01/201, Adapter Shaft Alignment

 (4)  
AMM 28-11-00/201, Fuel Tanks

 (5)  
AMM 28-31-00/501, Fuel Jettison System

 (6)  
AMM 28-31-04/401, Fuel Jettison Transfer Valve Actuator

 E.
Access

 (1)  
Location Zones 544 Inbd Main Tank (Part), Mid Spar to Rear Spar, Left 571 Rear Spar to Landing Gear Support Beam, Left 644 Inbd Main Tank (Part), Mid Spar to Rear Spar, Right 671 Rear Spar to Landing Gear Support Beam, Right

 F.
Procedure

 S 144-032
 (1)  
Prepare these components for an electrical surface bond (SWPM 20-20-00):

 (a)  
Mating surfaces of the index plate and valve actuator.

 (b)  
Mating surfaces of the bonding jumper and bonding jumper tab.

 (c)  
AIRPLANES WITHOUT PRIMER BETWEEN THE SPAR AND THE ADAPTER PLATE; Mating surface of the front spar and adapter plate.

 NOTE: If the spar has a protective finish (primer coating)
____ under the adapter plate, it is not necessary to do this step.
 S 424-034
 (2)
Do these steps to prepare the adapter plate for installation:

 (a)
Lubricate the new O-ring with the petrolatum.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-31-13
 ALL  ú ú 01 Page 404 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (b) (c)  Install new packing in the groove on the adapter plate.Make sure the mating surface of the adapter plate is free from any petrolatum squeeze out.
 (3)  S 424-035Do these steps to install the adapter shaft: (a) Put the adapter shaft into the fuel tank through the opening in the rear spar. (b) Go into the fuel tank. (c) Engage the splines of the adapter shaft and valve body. (d) Install the bolts and washers (4 locations) that attach the adapter to the rear spar. (e) Install lockwire on the bolts.
 (4)  S 414-036Do these steps to close the fuel tank: (a) Close and go out of the fuel tank (AMM 28-11-00/201). (b) Install the applicable main tank access door(s) (AMM 28-11-02/401).
 (5)  S 824-042Do this task:  Adapter Shaft Alignment (AMM 28-00-01/201).
 (6)  S 424-037Install the actuator for the jettison transfer valve in the inboard main tank and the bonding jumper (AMM 28-31-04/401).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(67)