S 034-050

 (3)  
If you will remove transmission No. 1, 3, 6, or 8, remove the position transmitter (AMM 27-58-01/401).

 NOTE:  You will install the position transmitter after the ball
____
 screw adjustment.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 01 Page 402 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E. Install the TE flap lock onto the flap track carriages (Fig. 401):
 S 864-003
 (1)  
Supply electrical power (AMM 24-22-00/201).

 S 864-004

 (2)  
Move the flaps electrically to put the flap carriage in the correct position.

 (a)  
For the outboard flaps, the carriage must be approximately 1.95 inches (49.5 mm) forward of the fully down position.

 (b)  
For the inboard flaps, the carriage must be approximately 7.85 inches (199.4 mm) forward of the fully down position.

 S 864-006
 (3)  Remove the electrical power (AMM 24-22-00/201).
 S 494-007
 CAUTION:_______DO NOT MOVE THE FLAPS AFTER YOU INSTALL ONE FLAP LOCK. IF YOU CANNOT INSTALL THE SECOND LOCK, REMOVE THE FIRST LOCK AND READJUST THE FLAPS. YOU CAN CAUSE DAMAGE TO THE FLAP DRIVE MECHANISM.
 (4)  
If you will remove the transmission at flap track location 1 or 8, install the outboard trailing edge flap lock tool on the carriage of the outboard trailing edge flap at the location of the transmission that will be removed. If you will remove the transmission at flap track location 2 or 7, you must install a flap lock tool on both carriages of that flap.

 (a)  
Adjust the flap lock to the correct length.

 (b)  
Loosen the roller lock screws until the roller hook openings are clear.

 (c)  
Attach a safety cable to the airplane structure.

 (d)  
Put the hooks on the deadweight rollers of the forward bogie.

 (e)  
Adjust the roller lock screws to touch the rollers.

 (f)  
Adjust the flap position and/or the tool length to make sure you can put the pin thru the tool into the failsafe bar.

 NOTE: If the tool is adjusted too much at flap track location
____ number 2 or 7, you cannot install the pin at flap track location number 1 or 8.
 (g)  Tighten the star knob. Make sure that the serrations engage.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 01 Page 403 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

(REF) HOLE LOCATIONS INBOARD FLAP TRACK FAIL SAFE BAR 
BOGIE FORWARD  INBOARD TE FLAP LOCK 
INBOARD TE FLAPS 

FWD  FORWARD BOGIE  OUTBOARD FLAP TRACK OUTBOARD TE FLAP LOCK 
OUTBOARD TE FLAPS 
Figure 401 Flap Lock Installation

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-33
 ALL  ú ú 01 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 944-058
 CAUTION:_______DO NOT MOVE THE FLAPS AFTER YOU INSTALL ONE FLAP LOCK. IF YOU REMOVE A TRANSMISSION AT LOCATION NUMBER 2, 4, 5 OR 7, TWO LOCKS ARE REQUIRED ON THE APPLICABLE FLAP. IF YOU CANNOT INSTALL THE SECOND LOCK, REMOVE THE FIRST LOCK BEFORE YOU READJUST THE FLAPS. YOU CAN CAUSE DAMAGE TO THE FLAP DRIVE MECHANISM.
 (5)  
If you will remove the transmission at flap track location 3 or 6, install the inboard trailing edge flap lock on the carriage of the inboard trailing edge flap at the location of the transmission that will be removed. If you will remove the transmission at flap track location 4 or 5, you must install a flap lock on both carriages of that flap.

 (a)  
Adjust the tool to the correct length.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(68)