B.
Access
(1)
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)
667 Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
C. Procedure
S 864-023
(1) Do this task to pressurize hydraulic system No. 4: "Hydraulic System Pressurization" (Ref 29-11-00/201).
S 864-061
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
(2)
Put the flap control lever in the 30-unit detent to extend the outboard flaps and attach a DO-NOT-MOVE tag.
S 864-025
(3)
Do this task to depressurize hydraulic system No. 4: "Hydraulic System Depressurization" (Ref 29-11-00/201).
S 024-026
(4)
Remove the fairing attachment fitting (Fig. 401):
(a)
Hold the outboard flap track fairing in the extended position.
(b)
Disconnect the fixed drive link from the attachment fitting (Section C-C): 1) Remove the bolt, washers and nut that attach the pin to the
attachment fitting. 2) Remove the pin from the attachment fitting and the fixed drive link.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-45
ALL ú ú 01 Page 409 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c)
Remove the three bolts from the two sides of the flap track (Section D-D):
(d)
Remove the two bolts from the top of the flap track.
(e)
Remove the three bolts and washers from the bottom of the flap track.
(f)
Remove the attachment fitting and the shims.
(g)
Measure and write down the thickness of the shims.
TASK 27-51-45-404-027
7. Outboard Flap Track Fairing Support Fitting Installation________________________________________________________
A. References
(1)
IPC 27-51-44 Fig. 1 (Tracks No. 1 and 8).
(2)
IPC 27-51-50 Fig. 1 (Tracks No. 2 and 7)
B.
Access
(1)
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)
667 Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
C. Procedure
S 424-028
(1)
Install the fairing support fitting:
(a)
Adjust the support fitting to the length shown in Section A-A, Fig. 402.
(b)
Attach the support fitting to the fairing fitting (Section A-A, Fig. 401): 1) Install the bushings in the fairing fitting. 2) Put the support fitting in the fairing fitting. 3) Install the bolts, washers and nuts.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-45
ALL ú ú 01 Page 410 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
Outboard Flap Track Fairing Adjustment
Figure 402 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-45
ALL ú ú 01 Page 411 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
B
B
ACCESS PLATE
A
DRIVE ROD
FIXED
LINK SUPPORT FWD
FITTING
B
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(152)
