(7)  
Install the snubber block and shims on the outboard flap:

 (a)
Remove the snubber block and shims if they are installed.

 CAUTION:_______MONITOR THE FLAP MOVEMENT CAREFULLY. THE FLAPS CAN BE
 DAMAGED BY INCORRECTLY ADJUSTED COMPONENTS.

 (b)
Move the flaps and make sure the fairing moves correctly.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 01 Page 509 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  
Put the flap control lever in the UP detent to retract the flaps.

 (d)  
Install the snubber block, with the chamfer forward (Detail D):

 1)  Install the correct number of shims to make sure the movement of the spring is in the limits shown in Detail D.
 S 865-014
 (8)  
Put the flap control lever in the 30-unit detent to extend the flaps.

 S 835-015

 (9)  
Adjust the doors on fairings No. 1 and 8:

 (a)  
Adjust the forward door link to its maximum length and install the link (if it is necessary).

 (b)  
Put the flap control lever in the UP detent to retract the flaps.

 (c)  
Adjust the forward door link until the secondary door is aligned with the fairing, if it is necessary.

 NOTE: Do not turn the forward door link more than 1/2 turn.
____ The bulb seal on the forward edge of the door must touch the aftflap.
 Do not adjust the forward door link if there is not clearance between the seal and the aftflap.
 (d)  
Tighten the locknuts.

 (e)  
Install the lockwire on the checknuts.

 S 715-016
 (10)
 Extend and retract the flaps and make sure the fairing moves smoothly.

 E.  
Put the Airplane Back to Its Usual Condition.

 (1)
Put the flap control lever in the UP detent to retract the flaps.

 S 865-017

 (2)  
Do this task to depressurize hydraulic system No. 4: "Hydraulic System Depressurization" (Ref 29-11-00/201).

 S 865-019
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 01 Page 510 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 415-018
 (3)  Install the access panels on the applicable fairing: 567BB, 567CB, 567DB, and 567EB on track No. 1 565BB, 565CB, 565DB, and 565EB on track No. 2 665BB, 665CB, 665DB, and 665EB on track No. 7 667BB, 667CB, 667DB, and 667EB on track No. 8.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-31
 ALL  ú ú 01 Page 511 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 OUTBOARD FLAP TRACK FAIRINGS - INSPECTION/CHECK
_______________________________________________
 1.  General_______
 A.  There is one task in this procedure; an inspection of the outboard flap track fairing. To do the inspection, you measure the inner or outer diameters of the parts which attach the flap track fairings. The parts include the bushings, bolts, bearings, and pins.
 B.  The inspection is usually done before you install a fairing. You must remove the fairing to do the inspection.
 TASK 27-51-31-206-001
 2.  Outboard Flap Track Fairings Inspection_______________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0 to 1 inch (0 to 25 mm)

 (2)  
Micrometer - 1 to 2 inch (25 to 50 mm), To Measure Inner Dimensions

 (3)  
Micrometer - 1 to 2 inch (25 to 50 mm), To Measure Outer Dimensions

 (4)  
Vernier Caliper