H.
Adjust the ball screws.

 S 825-070
 (1)  
Adjust the ball screws if the ball screw nuts clearance at the upstop is out of the tolerance.

 S 865-019

 (2)
Release the pressure in hydraulic system No. 1 (Ref 29-11-00/201).

 S 215-071

 (3)  
Make sure that the flaps do not move.

 S 035-020

 (4)  
Disconnect the flap torque tubes at the transmissions:

 (a)  
Remove three screws which attach the coupling sleeve to the torque tube.

 (b)  
Move the coupling sleeve near the gearbox.

 S 835-021
 (5)  
Adjust the ball screws:

 (a)  
Use the manual drive tool to turn each transmission coupler until the ball screw nut and universal joint stops touch.

 (b)  
Connect the torque tube between the transmissions.

 (c)  
Turn the coupler one turn plus 19 teeth in the extend direction to move the flap ball screw nuts away from the stops.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-01
 ALL  ú ú 01 Page 506 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d)  Make sure that the clearance between the universal joint and the ball screw nut stop on each transmission is 0.72 inch
 (1.8 cm).
 S 435-022
 (6)  
Install the flap torque tubes:

 (a)  
Move the coupling sleeve on the torque tube.

 (b)  
Install the three screws that attach the coupling sleeve to the torque tube.

 CAUTION:_______MAKE SURE YOU INSTALL LOCKWIRE ON THE COUPLING SCREWS. IF THE COUPLING SCREWS COME OFF, THE TORQUE TUBE COUPLING WILL DISCONNECT AND CAUSE DAMAGE TO THE AIRPLANE.

 (c)  
Install the lockwire to hold the screws together.

 S 865-023
 (7)  
Pressurize hydraulic system No. 1 (Ref 29-11-00/201).

 S 225-024

 (8)
Make sure that dimension X is 0.54 to 0.90 inch (1.4 to 2.3 cm).

 S 865-025

 (9)
Release the pressure in hydraulic system No. 1 (Ref 29-11-00/201).

 I.  
Do a Check of the droop and symmetry of the inboard midflap and the inboard aileron:

 NOTE: Make sure the ball screw nuts are synchronized before you adjust
____ the droop and symmetry. Make sure that dimension X is 0.54 to
 0.90 inch (1.4 to 2.3 cm) for both of the ball screws. If not, see "Adjust the ball screws" and (Fig. 501, View A).
 S 865-088
 (1)  
Put the speed brake control lever in the UP detent to lift spoilers No. 5 thru 8 above the inboard flaps.

 S 495-089

 (2)  
Install the spoiler actuator locking tools or close the flight control shutoff valve for hydraulic system No. 4.

 (3)  
Make sure the inboard aileron is in the neutral position.

 (4)  
Pressurize hydraulic system No. 1 (AMM 29-11-00/201).

 S 865-090
 S 865-091
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-01
 ALL  ú ú 01 Page 507 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-102
 WARNING:_______ MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
 FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP
 CONTROL LEVER.  MOVING THE FLAP CONTROL LEVER WITH THE
 HYDRAULIC SYSTEM PRESSURIZED WILL CAUSE THE FLAPS TO MOVE
 QUICKLY.
 CAUTION:_______ MONITOR THE FLAPS CAREFULLY WHILE THEY RETRACT.  THE FLAPS CAN

 BE DAMAGED BECAUSE OF INCORRECTLY ADJUSTED COMPONENTS.
 (5)  Put the flap control lever in the UP detent to retract the flaps.
 NOTE: Control the hydraulic pressure to retract the flaps slowly.
____
 S 865-093
 (6)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(77)