27-48-01
 ALL  ú ú 01 Page 407 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Install the Transmitter Assembly
 S 424-037
 (1)  
Install the transmitter assembly onto the shear deck.

 (a)  
Install four assembly mounting bolts and the washers.

 S 434-038
 (2)  
Install the bolt, spacer, two washers, and nut to connect crank to the control rod.

 S 434-039

 (3)  
Install the bonding jumper.

 S 434-040

 (4)  
Install the electrical connector.

 E.
Adjust the Transmitter Assembly

 S 864-041
 (1)  
Do this task: "Supply Electrical Power" (Ref 24-22-00/201).

 S 864-042

 (2)  
Do this task: "Supply Hydraulic Power" (Ref 29-11-00/201).

 S 864-043

 (3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7E23, STAB TRIM ALTN CONT
 2) 7E20, STAB TRIM R S/O VALVE

 S 864-044
 (4)  Set the STAB TRIM 3 switch on the control stand to ON.
 S 864-045
 WARNING: MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE STABILIZER AND
_______ THE ELEVATOR SURFACES BEFORE YOU MOVE THE STABILIZER. THE STABILIZER AND THE ELEVATOR SURFACES CAN MOVE QUICKLY AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (5)  Use the STAB TRIM ALTN switches to move the stabilizer until the "B" dimension is 17.59-17.63 inches.
 NOTE: The "B" dimension is the distance along the ballscrew between
____ the surfaces of the ballnut and the ballscrew stops
 S 864-046
 (6)  Set the STAB TRIM 3 switch to CUTOUT.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-48-01
 ALL  ú ú 01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-047
 (7)  Open these circuit breakers and attach DO-NOT-CLOSE tag (a) P7, Overhead Circuit Breaker Panel 1) 7E20, STAB TRIM R S/O VALVE 2) 7E23, STAB TRIM ALTN CONT s:
 S 864-048
 (8)  Remove the DO-NOT-CLOSE tags and close these circuit br (a) P6, Main Power Distribution Panel 1) 6K23, STAB TRIM POSN IND L 2) 6K24, STAB TRIM POSN IND R (b) P7, Overhead Circuit Breaker Panel 1) 7C10, FLT CONT ELEC 2L AC 2) 7C11, FLT CONT ELEC 2L DC 3) 7C12, FLT CONT ELEC 1L AC 4) 7C13, FLT CONT ELEC 1L DC eakers:
 S 864-049
 (9)  If the hydraulic power is not necessary, do this task: Hydraulic Power" (AMM 29-11-00/201). "Remove
 S 834-050

 (10)
 Adjust the transmitter control rod:

 (a)  
Loosen the jamnut at the two ends of the applicable transmitter control rod.

 (b)  
Adjust the control rod until the applicable indication on the EICAS flight controls maintenance page shows 4.49-4.51 degrees down.

 (c)  
Tighten the jamnut at the two ends of the control rod.

 (d)  
Make sure the EICAS indication is in the tolerance.

 S 414-051
 (11)
 Close the 315A access door (AMM 06-09-05/201).

 S 864-055

 (12)
 Remove the DO-NOT-CLOSE tags and open these circuit breakers:

 (a)  
P414, Power Distribution Center Panel - Left 1) 414D8, CAPTAINS PWR SEAT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-48-01
 ALL  ú ú 03 Page 409 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  P415, Power Distribution Center Panel - Right
 1) 415H32, F/O PWR SEAT

 S 864-052
 (13)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7E7, STAB TRIM L S/O VALVE
 2) 7E20, STAB TRIM R S/O VALVE
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(27)