27-51-00
 ALL  ú ú 01 Page 207 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TE
_______ AND LE FLAPS BEFORE YOU MOVE THE FLAP CONTROL LEVER. THE TE AND LE FLAPS WILL MOVE AUTOMATICALLY WITH ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
 (a)  
Move the flap control lever to the 5, 10, 20, 25, or 30-unit detent to extend the flaps.

 (b)  
Make sure that the FLAPS display shows on the EICAS when you move the flap control lever. 1) The flap indicator bars will show in magenta color when the

 flaps start to move. 2) The flap indicator bars will change to green when the flaps are at the set position.
 S 862-048
 (5)  Extend the flaps in the alternate electric mode:
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TE
_______ AND LE FLAPS BEFORE YOU OPERATE THE ALTERNATE FLAPS CONTROL SWITCHES. THE TE AND LE FLAPS WILL MOVE AUTOMATICALLY WITH ELECTRICAL POWER WHEN YOU OPERATE THE ALTERNATE FLAPS CONTROL SWITCHES.
 (a)  
Push the ALTN FLAPS ARM switch on the pilots' center instrument panel to the ALTN position.

 (b)  
Turn the ALTN FLAPS EXT/RET switch on the pilot's center instrument panel to EXT.

 (c)  
Make sure that the FLAPS display shows on the EICAS when the ALTN FLAPS ARM switch is in the ALTN position.

 (d)  
Set the ALTN FLAPS EXT/RET switch to OFF when the flaps are in the correct position.

 WARNING: MAKE SURE ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE LE
_______ AND TE FLAPS AND FLAP DRIVE MECHANISMS. THE TE AND LE FLAPS WILL MOVE TO AGREE WITH THE CONTROL LEVER POSITION WHEN YOU DISARM ALTERNATE CONTROL. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (e) Move the flap control lever to the position of the flaps.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 01 Page 208 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (f)  Push the ALTN FLAPS ARM switch to the off position.
 S 862-050
 (6) Do this task: "Remove Electrical Power" (AMM 24-22-00/201).
 TASK 27-51-00-862-035
 7.  Trailing Edge Flaps Retraction with Electrical Power____________________________________________________
 A. General
 (1)  
There are two control modes to extend the flaps by electrical power: the primary electric mode and the alternate electric mode.

 (2)  
In the primary electric mode, you move the flap control lever to retract the flaps.

 (3)  
In the alternate electric mode, you use the ALTN FLAPS switches on the pilots' center instrument panel to retract the flaps.

 (4)  
Two of the three flap control unit inputs are from the relays R7774, ALT FLAP INBD TE, and R7775, ALT FLAP 2 OTBD. Circuit breakers TE FLAP ELEC CONT OTBD and TE FLAP ELEC CONT INBD supply power to these relays. If these two circuit breakers are pulled, the flaps will remain in the primary mode. If only one of the circuit breakers are pulled, the flaps will transition into the alternate mode. A FLAPS CONTROL EICAS caution message will be displayed when the flap system is in the alternate mode.

 B.
References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (3)  
SSM 27-51-02, 27-51-03

 (4)  
SSM 27-51-21, 27-51-22

 C.
Access

 (1)  
Location Zone
 221, 222 Control Cabin

 D.
Procedure

 (1)
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).

 S 862-025

 (2)  
Make sure hydraulic power is not supplied to systems 1 and 4 (AMM 29-11-00/201).

 S 862-052
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 10 Page 209 ú Jun 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(53)