S 484-060

 (2)  
Move the counter weight to make the spreader bar level.

 S 484-064

 (3)  
Attach the load positioner and spreader bar to the strongbacks.

 S 034-021

 (4)  
Remove four bolts (18), washers (16 and 19), and nuts (15) which connect the gimbal caps (17), ball screw nut and gimbal (Fig. 401).

 (a)  
Remove the gimbal caps from the ball screw nuts.

 (b)  
Move the ball screw away from the gimbal.

 S 024-072
 (5)  
If you will remove the forward bogies from the flap track, do the following:

 (a)  
Remove the bolts (12) and washers (13) from the stop fittings

 (6)
 on the lower surface of the track.

 (b)  
Remove the stop fittings (6) and shims (14).

 (c)  
Measure and record the shim (14) thickness.

 S 024-070
 (6)  If you will remove the forward bogies from the flap carriages, do the following:
 NOTE: Separation of the forward bogie from the flap track carriage
____ is not required for flap removal because the inboard flap track geometry allows the carriage and bogie to be removed as an assembly. Bogie removal is not recommended because of inherent danger to personnel.
 (a)  
Remove the cotter pins, nuts and washers from the support pins that attach the forward bogies to the carriages at both the left and right carriage locations.

 (b)  
Manually move the flap to remove the flap weight from the forward bogies until all rollers on the forward bogies may be freely rotated.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-01
 ALL  ú ú 01 Page 411 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WARNING: REMOVING THE SUPPORT PIN WITH THE FLAP WEIGHT ON THE
_______ FORWARD BOGIE MAY CAUSE THE FLAP TO MOVE SUDDENLY. PERSONNEL CAN BE INJURED OR EQUIPMENT DAMAGED.
 (c)  
Remove the support pins and washers and measure and record the thickness of the washers as they are removed.

 (d)  
Remove the bushings from the bolt holes in the bogies.

 S 024-071
 (7)  Move the flap assembly (1) aft. Permit the bogies to move from the flap tracks if they are attached to the flap carriages.
 NOTE: Make sure that the flap is held correctly when it is
____ removed. The flap weighs approximately 2000 pounds (900 kg).
 S 094-024
 (8)  
Remove the tools from the midflap and aftflap.

 H.
If a replacement flap or midflap will be installed, do these steps:

 S 014-025
 (1)  
From the top surface of the midflap, remove access panels 577 ET and 577 BT (on the left side) or 677 ET and 677 BT (on the right side).

 S 034-026

 (2)  
Remove the bolts (23), washers (24 and 27), and nuts (28) which attach the support fitting (25) for the main carriage bearing. Remove the support fitting.

 S 224-027

 (3)  
Measure the thickness of the shim pack (26) between the support fitting for the main carriage and the midflap frame.

 S 934-052

 (4)  
Attach a label to the midflap with the thickness of the shim pack.

 S 434-028

 (5)  
Use the bolts, washers, nuts, and shims to install the support fitting.

 NOTE: Install the shims below the nut.
____
 S 414-029
 (6)  Install the access panels.
 TASK 27-51-01-404-030
 3. Inboard Flap Installation
_________________________
 A. Special Tools and Equipment
 (1)  10OHME65B00116 Trailing Edge Flap Spreader Bar
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-01
 ALL  ú ú 01 Page 412 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(69)