MAXIMUM
WEAR ALLOWANCE 2`
(ANGULAR BACKLASH)

SEE A
A-A
SPLINE COUPLING SLEEVE
SPLINED
COUPLER
SPROCKET

0.03 INCH
MAXIMUM WEAR ALLOWANCE (PITCH LINE BACKLASH)
LARGER VIEW OF SAMPLE TEETH SPLINE
A
Flap Torque Tube Splined Coupler Wear Limits
Figure 601

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-20
 ALL  ú ú 01 Page 603 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 226-008
 (2)  
Examine the center sleeve bearings:

 (a)  
Measure the radial depth of the worn area at the center sleeve bearing.

 NOTE: The torque tube can be worn to 0.040 inch (1.02 mm)
____ maximum radial depth on the phenolic sleeve.
 (b)  Replace the torque tube if it is not in the limits.
 S 226-009
 (3)  
Examine the air sealer on the flap torque tube.

 (a)  
Examine the seal assembly for cracks or deterioration.

 (b)  
Examine the seal assembly for worn areas. 1) The inner diameter of a carbon seal must not be more than

 2.02 inches (5.13 cm). 2) The worn area on a carbon seal must not be more than
 0.02 inch (0.5 mm) from the seal retainer.
 (c)  Replace the seal assembly if it is necessary
 (AMM 27-51-20/401).

 S 226-016
 (4)  
AIRPLANES WITH RIVETS AT TORQUE TUBE END FITTINGS;
 Examine the torque tube for loose rivets:

 (a)  
Make sure there is no movement between the end fitting and the tube.

 (b)  
If there is movement between the end fitting and the tube do one of these procedures: 1) Replace any torque tube which shows movement between the

 end fitting and the torque tube (AMM 27-51-20/401).
 2) Repair any torque tube which shows movements between the
 end fitting and the torque tube (AMM 27-51-20/801).

 E. Put the Airplane Back To Its Usual Condition
 S 866-010
 (1)  
Pressurize hydraulic systems No. 1 and 4 (AMM 29-11-00/201).

 (2)
Put the flap control lever in the UP detent to retract the flaps.

 S 866-014

 (3)  
Release the pressure in hydraulic systems No. 1 and 4
 (AMM 29-11-00/201).

 S 866-011
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-20
 ALL  ú ú 01 Page 604 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 096-012
 WARNING:_______ CAREFULLY DO THE SPECIFIED TASK TO REMOVE THE DOOR LOCKS FROM
 THE LANDING GEAR DOORS.  THE DOORS CAN CLOSE QUICKLY IF YOU DO
 NOT REMOVE THE DOOR LOCKS CORRECTLY.  THIS CAN CAUSE INJURY TO

 PERSONS AND DAMAGE TO EQUIPMENT.
 (4)  Remove the door locks from the doors for the body landing gear (AMM 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-20
 ALL  ú ú 01 Page 605 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 FLAP TORQUE TUBE - REPAIRS
__________________________
 1.  General
_______
 A.  There are three tasks in this procedure. There is one task for the repair of a flap torque tube. There is one task to make a splice in a flap torque tube. There is also a task to install a flap torque tube coupling.
 B.  AIRPLANES WITH ELECTROMAGNETIC FORMING (EMF) END FITTINGS; No play is permitted on EMF end fittings. If the end fittings do become loose, replace the torque tube (AMM 27-51-20/401).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(177)