EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-17
ALL ú ú 02 Page 406 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
WARNING: MAKE SURE ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE LE
_______ AND TE FLAPS AND FLAP DRIVE MECHANISMS. THE TE AND LE FLAPS WILL MOVE TO AGREE WITH THE CONTROL LEVER POSITION WHEN ALTERNATE CONTROL IS DISARMED. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(e) Push the ALTN FLAPS ARM switch to disarm the alternate flap control.
S 094-042
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4) Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).
TASK 27-51-17-004-026
4. Outboard Flap Alternate Drive Motor Removal
___________________________________________
A. References
(1)
AMM 29-11-00/201, Main Hydraulic Supply System
(2)
AMM 32-00-30/201, Landing Gear Door Locks
(3)
AIPC 27-51-09, Fig. 3
B.
Access
(1)
Location Zones
138 Body Landing Gear Wheel Well, RH
C.
Prepare for the Removal
S 864-029
(1)
Do this task to depressurize hydraulic systems No. 1 and 4: "Hydraulic System Depressurization" (AMM 29-11-00/201).
S 864-031
(2)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6, Main Power Distribution Panel
1) 6L19, TE FLAP ELEC CONT OTBD
(b)
P415, Power Distribution Center-Right 1) 415M38, TE FLAP ELEC OTBD
(3)
Make sure that the landing gear ground locks are installed.
S 864-033
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-17
ALL ú ú 01 Page 407 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 494-035
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4)
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).
D.
Remove the Outboard Drive Motor
S 034-006
(1)
Disconnect the electrical connector (6) from the drive motor (5).
S 024-007
(2)
Remove the outboard drive motor:
(a)
Remove the bolts (2, 3, and 7), washers (1), and the nut (4) which attach the drive motor to the flap power package.
(b)
Remove the drive motor from the power package.
(c)
Put a cover on the opening in the power package.
TASK 27-51-17-404-010
5. Outboard Flap Alternate Drive Motor Installation
________________________________________________
A. Consumable Materials
(1)
C00259, Enamel - Primer, Green, BMS 10-11
(2)
D00633, Grease - BMS 3-33 (recommended)
(3)
D00013, Grease - MIL-G-23827 (alternative)
(4)
B00192, Solvent - BMS 3-2, Type 1
B.
Parts
~.............................................................................. | MM | | IPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Washer | 27-51-09| 03 | 482 or | | | | | | | 487 | | | 2 | Bolt | | | 477 | | | 3 | Bolt | | | 467 | | | 4 | Nut | | | 492 | | | 5 | Drive Unit (Motor) | | | 497 | | | 7 | Bolt | | | 462 or | | | | | | | 472 | 2......…........…...................................…..........….....….........1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(160)
