(c)  
7C12, FLT CONT ELEC 1L AC

 (d)  
7C13, FLT CONT ELEC 1L DC

 (e)  
7C14, FLT CONT ELEC 1R AC

 (f)  
7C15, FLT CONT ELEC 1R DC

 (g)  
6C16, FLT CONT ELEC 2R AC

 (h)  
7C17, FLT CONT ELEC 2R DC

 S 862-055
 (2)  Make sure the ALT FLAPS ARM switch is off.
 TASK 27-51-00-002-001
 10. Flap Track Fairing Removal (Fig. 201)
__________________________
 A. General
 (1)  When you cannot extend the trailing edge flaps because of failure of a transmission or other flap drive component, you must remove the flap track fairings to get access to the failed component. This is a general procedure to remove the inboard or outboard fairings. It can be necessary to change the procedure for the specific component failure.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 02 Page 216 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
SEE C
SEE  B 
SEE  D 
SEE  E 
A 
TIEBOLT 
TIEBOLT 
LOCK 
HINGE 
FITTING  RETAINER 

JUMPER BONDING  TIEBOLT 
ROD (3 LOCATIONS) ADJUSTABLE  FIXED FAIRING  FIXED FAIRING EXTENSION  FIXED FAIRING 1 
B 
C 
1  FAIRINGS NO. 3 AND 6 HAVE A TIEBOLT ON EACH SIDE OF THE FAIRING 
Figure 201 (Sheet 1) Flap Track Fairing Removal 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 02 Page 217 ú Jun 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

HINGE FITTING  BOLT (2 LOCATIONS) FORWARD HINGE 
BONDING JUMPER 
MOVABLE FAIRING ACCESS PLATE 
D 
FWD 
ADJUSTABLE ROD ACCESS PLATE 
FLAP TRACK FAIRING  (2 LOCATIONS) AFT HINGE BOLT 
(OTHER FAIRINGS EQUIVALENT) LINKAGE SHOWN IN RETRACTED POSITION FAIRING NO. 2 AND 7 E 
Figure 201 (Sheet 2) Flap Track Fairing Removal 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 02 Page 218 ú Jun 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
You cannot use the usual equipment to remove the fairing with the flaps retracted. Use a maintenance stand or other equipment to hold the fairing. The inboard fairing weighs approximately 110 pounds and the outboard fairing approximately 80 pounds.

 (3)  
After you repair the flap system, you can install the flap track fairings with the usual installation procedures. Refer to 27-51-26/401 for the inboard flaps or 27-51-31/401 for the outboard flaps.

 B.
References

 (1)  
AMM 29-11-00/201, Main Hydraulic Supply System

 C.
Access

 (1)  
Location Zone
 567 Outboard Flap Track Fairing, Outboard Flap, LH,
 (Track No. 1)
 565 Inboard Flap Track Fairing, Outboard Flap, LH,
 (Track No. 2)
 563 Outboard Flap Track Fairing, Inboard Flap, LH,
 (Track No. 3)
 561 Inboard Flap Track Fairing, Inboard Flap, LH,
 (Track No. 4)
 661 Inboard Flap Track Fairing, Inboard Flap, RH,
 (Track No. 5)
 663 Outboard Flap Track Fairing, Inboard Flap, RH,
 (Track No. 6)
 665 Inboard Flap Track Fairing, Outboard Flap, RH,
 (Track No. 7)

 667  Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)

 (2)  
Access Panels

 (a)  
Track No. 1 567BB Outboard Flap Track Fairing, Outbd Flaps 567CB Movable Flap Track Fairing, Outbd Flaps 567DB Movable Flap Track Fairing, Outbd Flaps 567EB Movable Flap Track Fairing, Outbd Flaps
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(57)