S 424-036
 (2)  
Align the tension studs on the bottom of the forward sill with the floor fittings while you lower the sill.

 S 424-037

 (3)  
Move the forward sill approximately 3.0 inches in the forward direction.

 S 424-038

 (4)  
Align the tension studs on the bottom of the aft sill with the floor fittings while you lower the sill.

 S 424-039

 (5)
Move the aft sill approximately 1.5 inches in the aft direction.

 S 424-040

 (6)  
Move the forward sill approximately 1.5 inches in the aft direction.

 S 434-041

 (7)  
Lower the shear-plunger levers to extend the shear-plunger studs into the floor fittings.

 NOTE: This will lock the sill assembly to the floor fittings.
____
 S 824-073
 (8)  If this is the first installation of the sill assembly, do this task: "Sill Assembly Adjustment".
 D. Put the Airplane Back to Its Usual Condition
 S 414-044
 (1)  
Install the rollout guide/stops, rail supports, and the
 guide/restraint rails which you removed (Ref 25-58-02/401).

 S 094-045

 (2)  
Remove the safety strut for the side cargo door (Ref 52-32-16/401).

 S 414-046
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE AWAY FROM THE DOOR AND
_______ THE DOOR OPENING WHEN YOU OPERATE THE DOOR. FAILURE OF THE LIFT MECHANISM COULD CAUSE THE DOOR TO CLOSE QUICKLY WHICH COULD CAUSE INJURY OR DAMAGE.
 (3)  Close the side cargo door (Ref 52-32-00/001).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-57-03
 ALL  ú ú 01 Page 404 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 TASK 25-57-03-204-047
 4.  Sill Assembly Inspection/Check (Fig. 401)______________________________
 A. General
 (1)  This task gives instructions to measure the clearance between the sill support fittings and the door latch fittings. The sill support fittings are on the bottom of the two outboard sills. There are five sill support fittings on each outboard sill. The door latch fittings are on the structure below the outboard sills.
 B. References
 (1)  
52-32-00/001, Side Cargo Door

 (2)  
52-32-16/401, Side Cargo Door Safety Strut

 C. Access
 (1)  Location Zone
 210 Main Deck

 D. Prepare for the Inspection/Check
 S 014-048
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE AWAY FROM THE DOOR AND
_______ THE DOOR OPENING WHEN YOU OPERATE THE DOOR. FAILURE OF THE LIFT MECHANISM COULD CAUSE THE DOOR TO CLOSE QUICKLY WHICH COULD CAUSE INJURY OR DAMAGE.
 (1)  
Open the side cargo door (Ref 52-32-00/001).

 S 494-049

 (2)  
Install the safety strut for the side cargo door if it is necessary (Ref 52-32-16/401).

 NOTE: It is optional to install the safety strut.
____
 S 494-050
 WARNING: BE CAREFUL WHEN YOU ARE NEAR THE OPENING OF THE SIDE CARGO
_______ DOOR. INSTALL THE PERSONNEL SAFETY NET ACROSS THE OPENING OF THE DOOR WHEN AN ACCESS STAND OR A PLATFORM IS NOT AT THE DOOR OPENING. THE MAIN DECK COMPARTMENT IS 16 FEET ABOVE THE GROUND. INJURY TO PERSONS CAN OCCUR IF THEY FALL THROUGH THE OPENING OF THE DOOR.
 (3)  Install the personnel safety net across the door opening if it is necessary.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-57-03
 ALL  ú ú 04 Page 405 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-019
 (4) Move the two outboard sills to the open position (not folded).
 E. Do an Inspection/Check of the Sill Assembly
 S 224-020
 (1)  Measure the horizontal clearance between the sill support fitting and the door latch fitting at the locations shown in Fig. 401.
 NOTE: The horizontal clearance must be 0.05-0.10 inch.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 2(82)