NOTE: Engine VSV systems that have been dynamically rigged, can
____ have a change to the N1/N2 speed relationship that will prevent the use of variable geometry condition results. A visual check of the MEC rig plate for alignment will show that a dynamic rig has been performed (AMM 75-31-00/501).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C12 Page 580D ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 12 - ENGINE DIAGNOSTIC RUN
___________________________________
B. Equipment
(1) AIRPLANES WITH FAN COWL PANELS WITHOUT A PART POWER RIG HOLE; Part Power Rig Pin (2) - C76001-1
NOTE: Part power rig pin C76001-1 is stored in a fly-away kit
____ located in electronics compartment (the kit is secured to the forward outboard leg of the battery support).
(2) AIRPLANES WITH FAN COWL PANELS WITH A PART POWER RIG HOLE;
Part Power Rig Pin (2) - C76001-2
NOTE: Part power rig pin C76001-2 is stored in a fly-away kit
____ located in electronics compartment (the kit is secured to the forward outboard leg of the battery support).
C. References
(1)
AMM 71-00-42/101, Power Plant, Power and Engine Response
(2)
AMM 71-00-59/101, Power Plant, Engine Checks
(3)
AMM 72-00-00/601, Engine
(4)
AMM 73-21-00/501, Fuel Control System
(5)
AMM 73-21-01/401, Main Engine Control
(6)
AMM 75-31-00/501, Variable Stator Vane Actuation System
(7)
AMM 75-32-05/501, Variable Bleed Valve Feedback Cable
(8)
AMM 76-11-00/501, Engine Control System
D.
Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
(2)
Access Panels
5737L/5837R Fan Cowl Assy
5746L/5846R Fan Cowl Assy
5738L/5838R Thrust Reverser Cowl Assy
5739L/5839R Thrust Reverser Cowl Assy
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-00
ALL ú ú C12 Page 580E ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 12 - ENGINE DIAGNOSTIC RUN
___________________________________
E. Procedure
S 715-035-C00
(1) Do an idle speed test on each engine (Test No. 4), and record the
low and high speeds on the engine run data sheet (Fig. 501).
NOTE: The engine data for the Idle Speed, Acceleration, Part
____ Power, and MPA tests can be collected in one continuous engine run before analysis. Or, the analysis and related corrective actions can be done after each power level check.
(a) Compare the low and high idle speeds.
1) If the idle speeds are out of limits, then adjust the idle speed (Test No. 4).
NOTE: If the low and high idle speeds are out of limits in
____ the same direction, this can indicate a fault with the MEC N2 speed governing system.
S 715-037-C00
(2) On each engine, do the part power trim test with the PMC OFF (Test No. 6); record the actual N2 speed and target N2 speed on the engine run data sheet.
NOTE: If you do the part power trim test with the PMC OFF, this
____ will help make sure that the MEC N2 speed governing system operates correctly and within limits.
(a) Compare the part power N2 speeds for each engine.
NOTE: N2 speeds must be within limits before you continue
____ with this test. If the MEC N2 speed governing is not correct, N1 speeds will also be incorrect.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(84)
