(a)  
Use the four ball lock pins.

 S 494-069-C00
 (4)  
Attach the forward lever hoists to the forward cradle mounts.

 S 494-070-C00

 (5)  
Attach the pulleys to the aft end of the cradle (Fig. 414).

 S 494-071-C00

 (6)
At the aft bootstrap location attach the cable to the dynanometer.

 S 494-072-C00

 (7)  
Put the cable through the cradle pulleys and attach it to the lever hoist.

 S 094-116-C00

 (8)  
Remove the hardware that attaches the cradle to the transportation base.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C08B Page 480B ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Power Plant Installation - Bootstrap Method
___________________________________________ Install the Power Plant
 S 494-117-C00
 CAUTION:_______ WHEN YOU RAISE THE ENGINE, DO NOT APPLY MORE THAN 4000 POUNDS
 (1820 KG) ON THE FORWARD OUTBOARD AND FORWARD INBOARD
 DYNAMOMETERS, AND 1000 POUNDS (454 KG) ON THE AFT DYNAMOMETER.
 DAMAGE TO EQUIPMENT CAN OCCUR.
 MAKE SURE THAT THE PRSOV DOES NOT HIT THE PRECOOLER DUCT WHEN
 YOU RAISE THE ENGINE.  DAMAGE TO THE PRECOOLER AND THE PRSOV
 CAN OCCUR IF THE PRSOV HITS THE PRECOOLER.
 MAKE SURE THAT THE CTAI DUCT CLAMP DOES NOT DAMAGE THE FORWARD
 FIRE SEAL ASSEMBLY ON ENGINE INSTALLATION
 MAKE SURE THAT THE POWER FEEDER CONNECTOR (D410) DOES NOT

 DAMAGE THE INLET COWL (IF INSTALLED) ON ENGINE INSTALLATION
 (9)  Raise the engine until it is approximately 6 inches (15 cm) below the strut and engine interfaces (Fig. 422).
 (a)  
Make sure the PRSOV does not hit the precooler.

 (b)  
Install new E-seals (2) in the bleed air duct and the precooler flanges (Fig. 405).

 (c)  
Make sure the starter duct does not hit the strut duct flange.

 1)  Install the metal seal (2) into the strut duct flange (Fig. 409).

 (d)  
Temporarily tie the power feeder connector (D410) and wire (Fig. 409) to the starter duct so that the connector does not stay on the inlet cowl (if installed). 1) If the inlet cowl is installed, the D410 connector can

 cause damage to the inlet cowl when the engine is raised to the strut.
 S 944-118-C00
 (10) Make sure all engine connections do not interfere with the strut as you raise the engine.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C13B Page 480C ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
AFT ENGINE MOUNT
CONE BOLT

THREAD PROTECTOR (INSTALLED)
6.0 INCHES (15 cm)
AFT ENGINE MOUNT ENGINEFIRE SEALS
FWD
A
Engine Installation - Aft Engine Mount Installation

Figure 422

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C10B Page 480D ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H56663
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Power Plant Installation - Bootstrap Method
___________________________________________ Install the Power Plant
 S 424-119-C00
 (11) Adjust the engine pitch until the forward and aft cone bolts go in their alignment holes at the same time.
 NOTE: On some power plant installations, it may be difficult to
____ align the forward cone bolts with the alignment holes on the engine mounts. When this occurs, manually push the engine until you get a better alignment, then keep this position until the engine is attached to the strut.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(134)