S 494-038-C00
 (6)  
Attach the inboard and outboard forward cradle mounts to the cradle (Fig. 413).

 (a)  
Use the four ball lock pins.

 (7)  
Attach the forward lever hoists to the forward cradle mounts.

 S 494-042-C00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C10B Page 450 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
FORWARD BOOTSTRAP INBOARD ARM
DYNAMOMETER
LEVER HOIST
SEEA
INBOARD CRADLE MOUNT
CRADLE
TRANSPORTATION BASE
FWD
NOTE: INBOARD VIEW SHOWN. OUTBOARD VIEW EQUIVALENT.
Forward Cradle Mount Attach Points
Figure 413 (Sheet 1)

C78275
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C10B Page 451 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
BALL LOCK PIN
INBOARD CRADLE
(2 LOCATIONS)
MOUNT
CRADLE
FWD AForward Cradle Mount Attach Points Figure 413 (Sheet 2)
E37666
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C10B Page 452 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Power Plant Removal - Bootstrap Method
______________________________________
 Install the Bootstrap Equipment

 S 494-039-C00
 (8)  Attach the pulleys to the aft end of the cradle (Fig. 414).
 (a)  Use the ball lock pins.
 S 494-040-C00
 (9)  
At the aft bootstrap location attach the cable to the dynamometer.

 S 494-041-C00

 (10)
 Put the cable through the cradle pulleys and attach it to the lever hoist.

 S 984-042-C00

 (11)
 Align the transportation base/cradle assembly below the engine as follows:

 (a)  
Raise the transportation base/cradle assembly with the forward and aft lever hoists until it is aligned with the engine.

 (b)  
Lower the transportation base/cradle assembly to the ground.

 S 094-043-C00
 (12)
 Release the cradle assembly from the transportation base.

 S 484-258-C00

 (13)
 Set the dynamometers to the zero position.

 S 494-126-C00
 CAUTION: MAKE SURE YOU HAVE SUFFICIENT CLEARANCE WHEN YOU RAISE THE
_______ CRADLE ASSEMBLY. DAMAGE TO THE ENGINE CAN OCCUR IF THE CRADLE ASSEMBLY HITS THE ENGINE.
 (14)
 Raise the cradle up to the engine.

 (a)  As you raise the engine, make sure you align the attitude of
 the cradle with the attitude of the engine.

 (15)
 Attach the cradle to the engine as follows:

 S 494-044-C00
 NOTE: To remove the engine, you must attach the engine to the
____ cradle with the two fan case attach points and one of the two turbine frame attach points.
 (a) Do these steps to attach the fan case to the cradle (Fig. 415).
 1)  Remove the ball lock pins to release the inboard and outboard fan frame attach links from their retracted positions.
 2)  Turn the attach links 90 degrees and attach each to their fan frame attach points.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(123)