71-00-02
 ALL  ú ú C01B Page 409 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////

PAD FITTING
A

Thrust Reverser Hold-Open Rod Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITHOUT VIBRATION ISOLATORS FOR ú

 71-00-02
 THE FORWARD MOUNT/THRUST REVERSER HINGES ú ú C01B Page 410 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C64962
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE  B 
SAFETY PIN CLEVIS 
THRUST REVERSER 
COMPRESSION ROD FITTING 
PIN 
ADJUSTABLE SCREW 
FWD  BUMPER STOP THRUST REVERSER COMPRESSION PAD FITTING  CAP SCREWS (2 LOCATIONS) 
Thrust Reverser Hold-Open Rod Installation Figure 401 (Sheet 2) ____ RIGHT SIDE IS OPPOSITE. NOTE: LEFT SIDE SHOWN. BA 

C64966
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITH VIBRATION ISOLATORS FOR THE ú

 71-00-02
 FORWARD MOUNT/THRUST REVERSER HINGES  ú ú C01B Page 411 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Prepare For the Removal of the Power Plant
__________________________________________ Prepare the Airplane for the Removal of the Power Plant
 (d)  Do the above steps again to install the hold-open rod on the opposite thrust reverser.
 S 434-017-C00
 WARNING:_______ WHEN YOU INSTALL THE THRUST REVERSER HOLD-OPEN RODS, MAKE SURE
 THAT THREE OR MORE COMPLETE TURNS OF THE ADJUSTABLE SCREW ARE
 ENGAGED WITH THE TWO CLEVISES.  IF LESS THAN THREE TURNS OF THE
 THREADS ARE ENGAGED, THE HOLD-OPEN RODS CAN BREAK WHEN YOU
 DISCONNECT THE OPENING ACTUATORS.  THIS CAN CAUSE INJURIES TO
 PERSONS AND DAMAGE TO THE ENGINE AND THRUST REVERSER.

 (18) ENGINES WITH THE VIBRATION ISOLATORS FOR THE FORWARD MOUNT/THRUST REVERSER HINGES; Do these steps to attach the hold-open rods for the left and right thrust reversers (Fig. 401):
 NOTE: Make sure you install the correct thrust reverser hold-open
____ rod to the applicable left or right location. The hold-open rods are not interchangeable. Use the hold-open rod with the mark 'LEFT' for the left side and the hold-open rod with the mark 'RIGHT' for the right side.
 (a)  Use the attached cap screws and washers to attach the hold-open rod to the thrust reverser compression pad.
 NOTE: The cap screws and washers are attached to the
____ fitting when not in use.
 (b)  Align the inboard clevis end of the hold-open rod with the hole in the compression rod fitting.
 NOTE: The compression rod fitting is found on the strut
____ and aft of the precooler.
 (c)  
Install the pin with the handle end on the forward side. 1) Attach the safety pin to the end of the pin.

 (d)  
Do the above steps again to install the hold-open rod on the opposite thrust reverser.

 S 034-018-C00
 (19) Do these steps to disconnect the opening actuators for the thrust reverser (Fig. 402):
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C01B Page 412 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEEA
THRUST REVERSER
FWD
INSTALL A TIE HERE TO ATTACH THE OPENING ACTUATOR TO THE THRUST REVERSER
OPENINGACTUATOR
(VIEW IN THE AFT DIRECTION)
A
Thrust Reverser Opening Actuator Disconnections
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(111)