(b)
ENGINES WITH THE QUARTER TURN CLAMP; Install the fire extinquishing hose in the clamp and turn the quarter-turn fastener to attach the fire extinquishing hose to the fan air duct.
(c)
Attach the fire extinquishing hose and the pneumatic overtemperature sense hose to the bumper stop bracket with these fasteners: 1) ENGINES WITH THE WELDED SADDLE CLAMP;
Use the two bolts (7), washers (8), nuts (9) and clamp (10). 2) ENGINES WITH THE WELDED 'P-CLAMP'; Use the bolt (7), washer (8) and nut (9) and clamp (10).
S 434-089-C00
(2)
Use the clamp (1), washer (2) and nut (3) to connect the pneumatic overtemperature sense hose to the 5th-stage duct bracket (Fig. 404).
S 434-240-C00
(3)
Connect the pneumatic overtemperature sense hose to the tee fitting on the right side of the PRSOV as follows (Fig. 404):
(a)
Apply the antiseize compound to the tee fittings on the PRSOV.
(b)
Connect the pneumatic overtemperature sense hose to the tee fitting on the right side of the PRSOV.
S 434-091-C00
(4) Install the pressure sense line of the precooler control valve as follows (Fig. 404):
NOTE: If you do not apply the anti-seize compound, the
____
pneumatic fittings can become seized.
(a)
Apply the antiseize compound to the fittings on the sense line and the control valve.
(b)
Connect the sense line to the precooler control valve union.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-02
ALL ú ú C03B Page 480X ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Put the Airplane Back To Its Usual Condition
____________________________________________ Core Area Connections on the Right Side
S 434-094-C00
(5) Connect the electrical connectors as follows (Fig. 403):
(a) Install the top and bottom pieces of the PRSOV bracket. 1) Install the three bolts (9 and 10) and washers (11).
CAUTION: YOU MUST TURN THE CONNECTOR ELBOWS UNTIL THEY POINT DOWN.
_______ IF THE CONNECTOR ELBOWS DO NOT POINT DOWN, CLEARANCE PROBLEMS WITH THE FAN DUCT COWL AND THRUST REVERSER HALF CAN OCCUR AND POSSIBLY CAUSE EGT INDICATION FAULTS.
(b) Connect the electrical connectors D1208 and D1210 with the connector elbows pointed down.
NOTE: The table that follows gives the mating information
____ for the electrical connectors D1208 and D1210.
~................................................................ | ELECTRICAL CONNECTOR MATE WITH INFORMATION | ..................................................................
| | STRUT SIDE (RECEPTACLE) |
| ENGINE SIDE .......................................... ...
| (PLUGS) | STRUT NO. 1 | STRUT NO. 2 |
.................................................................. | D1208 | D3302 | D3304 | | D1210 | D3324 | D3326 | 2................................................................1
1) Tighten the electrical connector D1208 to 60-65
pound-inches (6.8-7.3 Newton meters).
a) Use the TG70 strap wrench (or equivalent). 2) Tighten the electrical connector D1210 to 30-35
pound-inches (3.4-4.0 Newton meters).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-02
ALL ú ú C12B Page 480Y ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Put the Airplane Back To Its Usual Condition
____________________________________________
Core Area Connections on the Right Side
(c) ENGINES WITHOUT THE CAPTIVE FASTENER CLAMPS;
Attach the clamp (6), bolt (2), washer (3) and nut (4) that
attach the W1508 wire bundle to the precooler.
NOTE:____ The clamp was attached to the wire bundle.
(d) ENGINES WITH THE CAPTIVE FASTENER CLAMPS;
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(143)
