B. There is one wingtip strobe position light in each wingtip.
C. The window in front of each light is sealed to prevent the possible entry of fuel fumes and water. When you do this procedure, you do not remove the window. You get access to the light through the access panel on the bottom of the wingtip.
TASK 33-45-11-962-001
2. Wingtip Strobe Position Lights - Lamp Replacement (Fig. 201)_________________________________________________
A. References
(1)
SSM 33-40-03
(2)
WDM 33-00-01, Lamp Usage Chart
(3)
WDM 33-43-01
B. Access
(1) Location Zone
301 Left Wing Tip
401 Right Wing Tip
C. Procedure
S 012-041
WARNING: DO NOT TOUCH THE LIGHT WITH YOUR BARE HANDS UNTIL THE LIGHT IS
_______ OFF FOR A MINIMUM OF FIVE MINUTES. DURING THIS TIME, YOU CAN RECEIVE AN INJURY IF YOU TOUCH THE LIGHT. THE LIGHT CAN BURN YOUR SKIN OR GIVE YOU AN ELECTRICAL SHOCK.
(1)
Do the task, Wingtip Strobe Position Light Removal, to remove the light from the wingtip.
S 022-026
(2)
Carefully replace the lamp.
(a)
Remove the screws from the cover.
(b)
Remove the cover from the light.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STROBE ú
33-45-11
POSITION LIGHTS ú ú 02 Page 201 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c)
Remove the lockwire from the lamp receptacle.
(d)
Pull out the lamp.
CAUTION:_______DO NOT TOUCH THE NEW LAMP WITH YOUR BARE HANDS. THE OILS FROM YOUR SKIN CAN CAUSE THE LAMP TO BREAK WHEN THE LAMP COMES ON AND BECOMES HOT.
(e)
Install the new lamp. 1) Make sure the new lamp is free from oil, grease, and fingerprints. 2) To hold the lamp, use a cloth or a glove which is clean and
soft. 3) Push the lamp into the lamp receptacle. 4) Attach the lockwire to the lamp receptacle.
(f)
Clean the lens with a clean, soft, dry cloth.
(g)
Install the lens assembly with the screws.
S 412-011
(3) Do the task, Wingtip Strobe Position Light Installation, to install the light in the wingtip.
TASK 33-45-11-002-012
3. Wingtip Strobe Position Light Removal (Fig. 201)_____________________________________
A. References
(1)
SSM 33-40-03
(2)
WDM 33-43-01
B. Access
(1) Location Zone
301 Left Wing Tip
401 Right Wing Tip
C. Procedure
S 862-013
(1) Do one of these steps to remove electrical power from the wingtip strobe position light:
(a) Open each applicable circuit breaker and attach the DO-NOT-CLOSE tag: 1) On the load control center panel, P18.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STROBE ú
33-45-11
POSITION LIGHTS ú ú 02 Page 202 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
ASEE WINGTIP STROBE POSITION LIGHT
ASEE WINGTIP STROBE POSITION LIGHT WINDOW SEE B POSITION LIGHT WINGTIP STROBE 1LIGHT (REF) (NAVIGATION) STEADY POSITION LIGHT (REF) (NAVIGATION) STEADY POSITION
FWD OUTBD
ACCESS PANEL
WINGTIP STROBE POSITION LIGHT
A
BRACKET MOUNTING SCREW (4 LOCATIONS) LAMP LENS ASSEMBLY
LAMP RECEPTACLE WITH A LOCKWIRE
(4 LOCATIONS) MOUNTING SCREW (4 LOCATIONS) MOUNTING BOLT
CONNECTOR ELECTRICAL
1 IF INSTALLED B WINGTIP STROBE POSITION LIGHT
Figure 201 Wingtip Strobe Position Lights
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STROBE ú 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(87)
