S 032-007
 (2)  Remove the lens.
 (a)  
Remove the screws from the lens retainer.

 (b)  
Remove the lens retainer and the lens.

 S 962-006
 (3)  
Carefully replace the lamp.

 S 432-008

 (4)  
Install the lens.

 (a)  Clean the lens with a clean soft dry cloth.
 NOTE: Replace the lens, if the lens has a crack with a depth
____ that is more than 50% of its thickness. Also replace the lens, if the damage on its surface causes a decrease lighting intensity.
 (b)  
Put the retainer around the edge of the lens.

 (c)  
Hold the lens against the base of the light and install the screws in the retainer.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 33-43-11
 ALL  ú ú 01 Page 205 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Lamp Test
 S 862-009
 (1) Remove each DO-NOT-CLOSE or DO-NOT-OPERATE tag.
 (a) Close each circuit breaker that was opened.
 S 862-010
 (2) Set the switch to the on position.
 (a) Make sure the new lamp comes on correctly.
 S 862-011
 (3)
Set the switch to the off position.

 S 862-012

 (4)
Remove electrical power if it is not necessary (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 33-43-11
 ALL  ú ú 01 Page 206 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STEADY POSITION (NAVIGATION) LIGHTS - REMOVAL/INSTALLATION
__________________________________________________________
 1.  General_______
 A.  This procedure contains these tasks for the steady position light:
 (1)  
The removal of a red or green steady position light (referred to as a colored light).

 (2)  
The installation of a colored light.

 (3)  
The removal of a white steady position light (referred to as a white light).

 (4)  
The installation of a white light.

 B.  The colored lights are in each wingtip behind a window (Fig. 401). The wingtip is sealed to stop fuel fumes and water.
 (1)  To remove and install a colored light, you remove the access panel below the wingtip. You do not remove the window.
 TASK 33-43-11-004-025
 2.  Colored Steady Position Light - Removal (Fig. 401)_______________________________________
 A.  Access
 (1)  
Location Zone
 301 Left Wing Tip
 401 Right Wing Tip

 (2)  
Access Panels
 7176 Left Wingtip Access Panel
 7576 Right Wingtip Access Panel

 B.  Procedure
 S 864-028
 (1)  Do one of these steps to remove electrical power from the steady position light:
 (a)  
Open each applicable circuit breaker and attach the DO-NOT-CLOSE tag: 1) On the load control center panel, P18.

 (b)  
At the overhead panel, P5, set the switch to the off position and attach the DO-NOT-OPERATE tag.

 S 014-024
 (2)  Get access to the colored light.
 (a)  Remove the screws that hold the access panel and remove the panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 33-43-11
 ALL  ú ú 01 Page 401 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
COLORED STEADY POSITION LIGHTS (RED)
SEE A
WHITE STEADY
POSITION LIGHT
SEE C
WHITE STEADY COLORED STEADY
POSITION LIGHT
POSITION 
LIGHTS (GREEN)  SEE  C  WINDOW  COLORED STEADY 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(77)