you will do the test on.
 CAUTION:_______ WHEN YOU TURN THE ANTISKID TRANSDUCER, DO NOT ATTACH
 A METAL FITTING DIRECTLY ON THE TRANSDUCER.  DAMAGE
 TO THE EQUIPMENT CAN OCCUR.  IF YOU USE A METAL
 FITTING, PUT A PROTECTIVE COVER ON THE ANTISKED
 TRANSDUCER.

 2)  Turn the transducer while you do a check to make sure that you do not have these conditions: a) Too much free play of the bearing. b) A drive shaft that is bent.
Do these steps to prepare to do a test of the electrical operation of the transducer: 1) Open this circuit breaker on the P6 main power distribution
 panel and attach a DO-NOT-CLOSE tag:
 a) ANTISKID FAIL WARN & PARK BRAKE 2) Make sure that the parking brake is released. 3) Disconnect the electrical connector D928 from the parking
 brake shutoff valve. 4) Make sure that the ANTISKID INOP light on the pilot's panel comes on.
 5)  Remove the DO-NOT-CLOSE tag and close this circuit breaker on the P6 main power distribution panel: a) ANTISKID FAIL WARN & PARK BRAKE
 6) Set the parking brake.
Do this test if you installed a transducer on the left outboard
 wheel:

 NOTE: You can see the brakes "apply" and "release" if you

____ watch the brake wear pins move. The pins will extend farther out of the carrier when the brake releases (AMM 32-41-41/601).
 CAUTION: WHEN YOU TURN THE ANTISKID TRANSDUCER, DO NOT ATTACH
_______ A METAL FITTING DIRECTLY ON THE TRANSDUCER. DAMAGE TO THE EQUIPMENT CAN OCCUR. IF YOU USE A METAL FITTING, PUT A PROTECTIVE COVER ON THE ANTISKID TRANSDUCER.
 1)  Turn the left outboard transducer drive coupling to
 approximately 500-1000 RPM . 2) Make sure that the right outboard brake releases. 3) Stop the movement of the transducer as quickly as possible.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-42-11
 ALL  ú ú 02 Page 405 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (l)

(m)

A
737-300/400/500MAINTENANCE MANUAL
 4) Make sure that the left outboard brake releases momentarily
 and then applies again in 5 to 10 seconds.Do this test if you installed a transducer on the left inboard wheel:
 NOTE: You can see the brakes "apply" and "release" if you
____ watch the brake wear pins move. The pins will extend farther out of the carrier when the brake releases (AMM 32-41-41/601).
 CAUTION: WHEN YOU TURN THE ANTISKID TRANSDUCER, DO NOT ATTACH
_______ A METAL FITTING DIRECTLY ON THE TRANSDUCER. DAMAGE TO THE EQUIPMENT CAN OCCUR. IF YOU USE A METAL FITTING, PUT A PROTECTIVE COVER ON THE ANTISKID TRANSDUCER.
 1) Turn the left inboard transducer drive coupling to
 approximately 500-1000 RPM . 2) Make sure that the right inboard brake releases. 3) Stop the movement of the transducer as quickly as possible. 4) Make sure that the left inboard brake releases momentarily
 and then applies again in 5 to 10 seconds.Do this test if you installed a transducer on the right inboard wheel:
 NOTE: You can see the brakes "apply" and "release" if you
____ watch the brake wear pins move. The pins will extend farther out of the carrier when the brake releases (AMM 32-41-41/601).
 CAUTION: WHEN YOU TURN THE ANTISKID TRANSDUCER, DO NOT ATTACH
_______ A METAL FITTING DIRECTLY ON THE TRANSDUCER. DAMAGE TO THE EQUIPMENT CAN OCCUR. IF YOU USE A METAL FITTING, PUT A PROTECTIVE COVER ON THE ANTISKID TRANSDUCER.
 1) Turn the right inboard transducer drive coupling to
 approximately 500-1000 RPM. 2) Make sure that the left inboard brake releases. 3) Stop the movement of the transducer as quickly as possible. 4) Make sure that the right inboard brake releases momentarily
 and then applies again in 5 to 10 seconds.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-42-11
 ALL  ú ú 02 Page 406 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (n)  Do this test if you installed a transducer on the right outboard wheel:
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(62)