(f)  
Install the lower flanged bushing (8).

 (g)  
Make sure the clearance between the forward and the aft collar halves is 0.02 |0.01 inch.

 CAUTION:_______MAKE SURE YOU FOLLOW THE CURE TIME OF THE SEALANT. THIS IS IMPORTANT WHEN YOU LUBRICATE THE BEARING. IF THE SEALANT WILL NOT CURE PROPERLY, DAMAGE TO THE STEERING COLLAR BEARING WILL WILL OCCUR.

 (h)  
Add fillet seal and fill the clearance with sealant.

 (i)  
Lubricate the steering collar (AMM 12-21-21/301).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-61
 ALL  ú ú 03 Page 406 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (4)  S 434-015Install the retaining pin (18) to the upper torsion link (AMM 32-21-31/401).
 (5)  S 714-016Make sure the steering collar can move freely. (a) Hold the torsion link horizontally. 1) Apply a maximum force of 5 pounds horizontally to the top end of the link. (b) Make sure the steering collar is free to turn 90 degrees in the two direction.
 S 644-036

 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT CAN OCCUR.
 (6)  
Apply a layer of the compound to the right and the left bolts and bolt bushings (8 and 11) of the steering collar (AMM 12-21-21/301).

 S 844-018

 (7)  
Turn the steering collar to approximately 55 degrees to the left side.

 (a)  
Install the right bolt and the bolt bushings (8 and 11) of the steering collar.

 S 434-019
 (8)  Tighten the nut to 600 - 700 pound-inches of lube torque.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-61
 ALL  ú ú 01 Page 407 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 844-020
 (9)  
Turn the steering collar to approximately 110 degrees to the right side.

 (a)  
Install the left bolt and the bolt bushings (8 and 11) of the steering collar.

 S 434-021
 (10)
 Tighten the nut to 600 - 700 pound-inches of lube torque.

 S 424-022

 (11)
 Install the steering system cables.

 (a)  
Remove the tape from the cables wind into the coil to the trunnion.

 (b)  
Install the cable terminals (NWSA and NWSB) in the recess in the grooves on the aft side of the steering collar (20). 1) AIRPLANES WITH TWO CABLES;

 Install the spring pins (22) on the steering collar (20). a) Install the lockwire (21) on the spring pins (22).
 2)  AIRPLANES WITH ONE CABLE; On steering cylinder with single cable, install the cotter pins (21) on the steering collar (20).
 S 834-023
 (12)
 Adjust the cable tension (AMM 32-51-00/501).

 (13)
 Install the apex bolt of the torsion link.

 S 094-025

 (14)
 Remove the rigging pin behind the steering wheel in the flight compartment.

 (15)
 Make sure the steering system will operate (AMM 32-51-00/501).

 S 434-024
 S 714-026
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-61
 ALL  ú ú 01 Page 408 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STEERING COLLAR - INSPECTION/CHECK
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(142)