曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT CAN OCCUR.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-51
 ALL  ú ú 02 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (1)  Clean the upper (4), and the lower (12) support plates then apply a light layer of grease to the mating or the bearing surfaces.
 NOTE: Apply a layer of Mastinox 6856K to parts which are not
____
 lubricated with grease after installation.

 NOTE: Apply a layer of MIL-PRF-23827, or the preferred grease BMS
____ 3-33 to parts which are lubricated with grease after installation (AMM 12-20-00/301).
 NOTE:____The support plates are sets. If you replace one plate, you must machine it to match with the other plate.
 S 434-115
 (2)  
Do the steps below to install the lower support plate (12):

 (a)  
Install the bearing (13) on the lower support plate (12).

 (b)  
Apply a thin layer of the compound, BMS 3-27, to the attach bolt (21) of the lower support plate.

 (c)  
Set the lower support plate (12) to the outer cylinder.

 (d)  
Install the attach bolt (21) of the lower support plate, washer (19), and the nut (18) to connect the lower support plate to the outer cylinder.

 (e)  
Tighten the nut (18).

 (f)  
Set the steering cylinder (11) on the lower support plate (12).

 (g)  
Fill the empty space between the lower trunnions of the steering cylinder and the lower support plate with corrosion preventive compound.

 (h)  
Install the washer (14), and the lower trunnion locknut (15) on the lower port of the steering cylinder (11).

 NOTE: Do not tighten the locknut, it should be loose at this
____
 time.

 S 434-116
 (3)  
Do the steps below to install the upper support plate (4):

 (a)  
Install the bearing (3) on the upper support plate (4).

 (b)  
Apply a thin layer of the compound, BMS 3-27, to the attach bolt (5) of the upper support plate.

 (c)  
Set the upper support plate (4) to the outer cylinder.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-51
 ALL  ú ú 02 Page 406 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  
Install the attach bolt (5) of the upper support plate, washer (22), and the nut (23) to connect the upper support plate to the outer cylinder.

 (e)  
Tighten the nut (23).

 (f)  
Set the steering cylinder (11) on the upper support plate (4).

 (g)  
Fill the empty space between the upper trunnions of the steering cylinder and the upper support plate with corrosion preventive compound.

 (h)  
Install the washers (6), (10), support plate spacers (7) between upper (4) and the lower (12) support plates.

 (i)  
Install the bolts (24), and (25) on the support plates.

 (j)  
Install the washer (2), and the upper trunnion locknut (1) on the upper port of the steering cylinder (11).

 NOTE: Do not tighten the locknut, it should be loose at this
____
 time.

 S 424-124
 (4)  Do these steps to make sure the steering cylinder (11) is centered with the steering collar lugs:
 NOTE: These instructions are to make sure that the rod end is
____ centered between the steering collar lugs before you tighten the two steering collar/rod end attach bolts per AMM 32-51-61/401. This is to prevent excessive pre-load on the actuator piston rod against one side of the gland.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(137)