HUBCAP FAIRING (OUTBOARD WHEELS ONLY)
WASHER  OUTER GREASED SEAL (IF INSTALLED)
TANG 1
CAM-LOC
FASTENERS

1 MAKE SURE THAT THE TANG OF
RETAINING RING
HUB CAP THE AXLE NUT RETAINER RING
(IF INSTALLED)
(OUTBOARD SHOWN EXTENDS THROUGH THE HOLES
INBOARD SIMILAR) IN BOTH THE AXLE NUT AND THE WASHER AFTER INSTALLATION
Main Gear Wheel Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-11
 ALL  ú ú 01 Page 402 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

INBD
A-A

Main Gear Wheel Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-11
 ALL  ú ú 01 Page 403 ú Mar 15/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 844-005
 WARNING:_______ BEFORE YOU REMOVE THE WHEEL AND TIRE ASSEMBLY YOU MUST DEFLATE
 THE TIRE OR DO AN EXAMINATION OF THE WHEEL AND TIRE ASSEMBLY TO
 MAKE SURE IT IS SAFE TO REMOVE WITHOUT DEFLATION.  DO THE
 EXAMINATION OF THE WHEEL AND TIRE ASSEMBLY OR DEFLATE THE TIRE
 AS GIVEN IN THE PROCEDURE THAT FOLLOWS.  A DEFECTIVE WHEEL AND
 TIRE ASSEMBLY CAN EXPLODE DURING OR AFTER REMOVAL IF YOU DO NOT
 DEFLATE THE TIRE.  THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE

 TO EQUIPMENT.
 (4)  Do step (a) to examine the tire and wheel assembly to see if it is safe to remove without tire deflation, or do step (b) to deflate the tire:
 NOTE: If you will not install the same wheel and tire assembly,
____ deflate the tire to prevent transporting and inflate tire.
 (a)  Examine the wheel and tire assembly to see if it has the conditions that follow: 1) The tires are not worn too much (AMM 32-45-00/601,
 Inspection Check). 2) The tire does not have damage. 3) The tires are cool enough to be comfortably touched with
 the bare hand. 4) There is no evidence of wheel damage, including cracked or missing tie bolts or tie nuts, or cracks in the wheel. 5) If the wheel and tire assembly does not have the conditions in the above steps, you must deflate the tires.
 (b)  Deflate the tire with the tire deflation tool.
 S 844-006
 WARNING:_______MAKE SURE THAT ALL PERSONS ARE CLEAR OF THE VALVE PATH. IF THE VALVE BLOWS OFF WHILE YOU REMOVE IT, INJURY TO PERSONS CAN OCCURE.
 WARNING:_______DO NOT USE TOO MUCH FORCE ON THE VALVE CORE. THE CORE PARTS CAN MOVE APART AND LET THE SLEEVE AND THE LOWER END OF POPPET STAY IN THE VALVE STEM.
 (5)  
If you cannot deflate the tire, slowly loosen the valve stem while you apply a slight pressure on the valve stem.

 S 024-007

 (6)  
Turn the eight Cam-Loc fasteners and remove the hubcap fairing (outboard wheels only).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-11
 ALL  ú ú 02 Page 404 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 024-008
 (7)
Remove the lockwire, bolts and washers, and remove the hubcap.

 S 024-009

 (8)
Remove the retainer ring of the axle nut.

 NOTE:____Some wheels have grease seals for the outer bearing. It is recommended that you keep the grease seal and the outer bearing in the wheel during wheel removal.
 S 024-010
 (9)
Remove the washer and the outer wheel bearing.

 S 484-011

 (10)
 Install the thread protector on the axle threads.

 S 024-012

 (11)
 Put the wheel change dolly in position, lift the wheel and remove it.

 S 484-043

 (12)
 Install the axle protector on the axle.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(107)