B.
Procedure

 S 584-038
 (1)  Lift the nose of the airplane with jacks until the tires clear of the ground (AMM 07-11-21/201).
 S 584-121
 CAUTION: DO NOT OPERATE THE STEERING WHEEL WITH THE SHOCK STRUT FULLY
_______ EXTENDED OR THE TORSION LINKS CONNECTED. DAMAGE TO THE CENTERING CAMS OF THE SHOCK STRUT CAN OCCUR IF YOU TRY TO OPERATE THE STEERING SYSTEM. MAKE SURE THE SHOCK STRUT IS COMPRESSED 2.10 INCHES OR MORE BEFORE YOU OPERATE THE STEERING SYSTEM. ALSO, THE DISTANCE BETWEEN THE BOTTOM SURFACE OR THE LOWER STEERING PLATE AND THE TOP SURFACE OF TOWING LUG MUST BE LESS THAN 21.90 INCHES.
 (2)  
Set the greased turning plates under the tires of the nose landing gear.

 S 584-084

 (3)  
Lower the airplane to the ground until the landing gear will support the airplane.

 S 864-036

 (4)  
Pressurize the hydraulic system A (AMM 29-15-00/201).

 S 214-035

 (5)  
Make sure the nose landing gear does not try to steer when you pressurize the hydraulic system A.

 (6)  
Make sure the steering wheel is in the center position.

 (7)  
Make sure the rudder pedals are in the neutral position.

 S 214-034
 S 214-033
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-51
 ALL  ú ú 02 Page 410 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 714-032
 (8)  
Turn the steering wheel counterclockwise to the left stop position and hold.

 (a)  
Make sure the nose landing gear steers approximately 78 degrees to the left.

 (b)  
Examine the actuator swivel for hydraulic leaks.

 S 714-031
 (9)  
Turn the steering wheel clockwise to the right stop position and hold.

 (a)  
Make sure the nose landing gear steers approximately 78 degrees to the right.

 (b)  
Examine the actuator swivel for hydraulics leaks.

 S 844-085
 (10)
 Make sure the steering wheel goes back to the neutral position.

 S 844-086

 (11)
 Make sure the nose landing gear goes back to the center position.

 S 584-029

 (12)
 Lift the nose of the airplane with jacks until the tires clear of the ground (AMM 07-11-21/201).

 (a)  
Remove the greased turning plates.

 S 584-028
 (13)
 Lower the airplane to the ground with the jacks (AMM 07-11-21/201).

 (14)
 Remove the jacks from the airplane.

 S 864-027

 (15)
 Remove the pressure from the hydraulic system A (AMM 29-15-00/201), if no longer needed.

 S 094-087
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-51
 ALL  ú ú 01 Page 411 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STEERING COLLAR - REMOVAL/INSTALLATION
______________________________________
 1.  General_______
 A.  This procedure contains two tasks:
 (1)  
The removal of the steering collar on the nose landing gear.

 (2)  
The installation of the steering collar on the nose landing gear.

 B.  
This procedure is for the removal and the installation of the steering collar only. Refer to AMM 32-51-51/401 for the removal and installation of the steering cylinders.

 TASK 32-51-61-004-027
 2.  Steering Collar Removal (Fig. 401)_______________________
 A.  Standard Tools and Equipment
 (1)  Rigging Pin - 0.311 + 0.000/-0.002 inch diameter x 6.0 inches long
 NOTE: The rigging pin is part of F70207-69 or F70207-78
____
 B.  References
 (1)  
AMM 29-15-00/201, Hydraulic System A and B

 (2)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(139)