S 865-517
(4)
If you will do no more tests, then do this task: "Put the Airplane to its Usual Condition."
TASK 31-24-01-735-518
36. EFIS Transfer Switch Signals Test_________________________________
A. Access
(1) Location Zones
101 Control Cabin - Left
102 Control Cabin - Right
B. Procedure
S 865-519
(1)
Make sure you did the Prepare For Input Parameter Test task.
S 735-520
(2)
Do this test of the signals from the EFIS transfer switch.
(a)
Set the portable tester to SUBFRAME 2, WORD 21.
(b)
Make sure the EFIS switch is in the NORM position.
(c)
Make sure the BIT 1 light on the portable tester is off.
(d)
Set the EFIS transfer switch to the BOTH-ON-2 position.
(e)
Make sure the BIT 1 light on the portable tester is on.
(f)
Put the EFIS transfer switch to the NORM position.
S 865-521
(3) If you will do no more tests, then do this task: "Put the Airplane to its Usual Condition."
TASK 31-24-01-735-536
37. Fire Warning Signals Test_________________________
A. Access
(1) Location Zones
101 Control Cabin - Left
102 Control Cabin - Right
B. Procedure
S 865-537
(1) Make sure you did the Prepare For Input Parameter Test task.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. BEJ 113 ú
31-24-01
ú ú 20B Page 545 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 865-538
(2) Open these circuit breakers: (a) P6-2 Panel 1) FIRE PROTECTION DETECTION APU 2) FIRE PROTECTION DETECTION ENG 1 3) FIRE PROTECTION DETECTION ENG 2
S 735-539
(3) Do this test of the fire signals from the wheel well: (a) Set the portable tester to SUBFRAME 0, WORD 27. (b) Set and hold the FAULT/INOP--OVHT/FIRE switch in the OVHT/FIRE position. (c) Make sure the wheel well light is on. (d) Make sure the BIT 2 light on the portable tester is on. (e) Release the FAULT/INOP--OVHT/FIRE switch. (f) Make sure the wheel well light is off. (g) Make sure the BIT 2 light on the portable tester is off.
S 865-540
(4) Open this circuit breaker: (a) P6-2 Panel 1) OVHT WHL WELL WING BODY
S 865-541
(5) Close this circuit breaker: (a) P6-2 Panel 1) FIRE PROTECTION DETECTION APU
S 735-542
(6) Do this test of the fire signals from the APU: (a) Set the portable tester to SUBFRAME 0, WORD 35. (b) Set and hold the FAULT/INOP--OVHT/FIRE switch in the OVHT/FIRE position. (c) Make sure the APU fire light is on. (d) Make sure the BIT 2 light on the portable tester is on.
NOTE:____ The APU fire light flashes. The BIT 2 light on the portable tester will only be on when the APU fire light is on.
(e) (f) (g) Release the FAULT/INOP--OVHT/FIRE switch.Make sure the APU fire light goes out.Make sure the BIT 2 light on the portable tester is off.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. BEJ 113 ú
31-24-01
ú ú 15B Page 546 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 865-543
(7) Open this circuit breaker:
(a) P6-2 Panel
1) FIRE PROTECTION DETECTION APU
S 865-544
(8) Close this circuit breaker:
(a) P6-2 Panel
1) FIRE PROTECTION DETECTION ENG 1
S 735-545
(9) Do this test of the fire signals from engine No. 1:
(a)
Set the portable tester to SUBFRAME 0, WORD 54.
(b)
Set and hold the FAULT/INOP--OVHT/FIRE switch in the OVHT/FIRE position.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 儀表 INSTRUMENTS(44)
