曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 Air = 1 (binary) Ground = 0 (binary) Bit 11 set to 1 (binary) Abnormal Start
 Where SDI means source/destination identifier, SSM means sign status matrix, and (L) equals engine 1 and (R) equals engine 2. The following table further defines status bits 30 and 31:
 ~........................................................ | STATUS BITS | | | ............... CONDITION | DATA | | 31 | 30 | | | .......................................................... | 1 | 1 | VALID (Normal) | NORMAL | | 1 | 0 | BITE (Functionaltest) | BITE Values | | 0 | 1 | Open Circuit Input (NCD) | Zero | | 0 | 0 | Internal Fault (Data Fail) | Zero | 2......…......…............................….............1
 NOTE: EGT parameters are limited to positive values.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EIS ú

 31-42-00
 ú ú 01 Page 205 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 TASK 31-42-00-802-025
 4. Erase Engine Exceedance Data without the Data Bus Analyzer
__________________________________________________________
 A. Procedure
 S 712-026
 (1)  
Make sure that the N1, EGT, and N2 indicators on both sides of the panel are not displaying exceedance values.

 S 712-027

 (2)  
Make sure that both N1 values are below 10%.

 S 422-028

 (3)  
On connector D10146 apply a ground to pin 3 for five to ten seconds.

 S 022-029

 (4)  
Remove the Ground from pin 3.

 S 862-030

 (5)  
Wait 3.5 to 4 minutes.

 S 422-031

 (6)  
Apply a ground to pin 4 for five to ten seconds.

 NOTE: This will reset the exceedance memory in the EIS Primary
____
 Display to zero.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EIS ú

 31-42-00
 ú ú 01 Page 206 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 ENGINE INSTRUMENT SYSTEM - ADJUSTMENT/TEST
__________________________________________
 1.  General_______
 A.  This procedure has these tasks:
 (1)  
A BITE test for the engine instrument system (EIS).

 (2)  
A functional test for the EIS.

 B.  The EIS BITE test monitors the internal health of the EIS Primary Display and EIS Secondary Display.
 C.  Functional tests of each display groups are not included in this section of the maintenance manual. The functional test task is a cross reference list that identifies the locations of all such tests.
 TASK 31-42-00-705-004
 2.  Engine Instrument System - BITE Test____________________________________
 A.  References
 (1)  AMM 24-22-00/201, Manual Control
 B.  Prepare for the Test
 S 865-001
 (1)  Make sure these EIS circuit breakers on the P6-2 LOAD CONTROL CENTER panel are closed:
 (a)  
EIS PRIMARY 1

 (b)  
EIS PRIMARY 2

 (c)  
EIS PRIMARY 3

 (d)  
EIS PRIMARY 4

 S 865-003
 (2)  Supply electrical power (AMM 24-22-00/201).
 C.  BITE test of EIS Primary Display
 S 715-006
 (1)  Set the DIM/BRT/TEST switch on the P1-3 or P2-1 panel to the TEST position.
 (a)  Make sure the N1, N2, and EGT red (over-limit) warning lights come on.
 S 715-009
 (2)  Release the DIM/BRT/TEST switch.
 (a)  Make sure the warning lights go off.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EIS ú

 31-42-00
 ú ú 01 Page 501 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 儀表 INSTRUMENTS(180)