S 434-021
(5)
Tighten the inlet and outlet lines.
S 614-023
(6)
Fill the hydraulic reservoirs if it is necessary (Ref 12-12-00/301).
TASK 27-81-71-714-006
4. Flap Flow-Limiting Valve Test (Standby System)______________________________________________
A. References
(1)
24-22-00/201, Manual Control
(2)
27-81-00/201, Leading Edge Flap and Slat Control System
(3)
12-12-00/301, Hydraulic Reservoir
B.
Access
(1)
Location Zone
101 Control Cabin, LH
102 Control Cabin, RH
216 Main Wheel Well, LH
C.
Procedure
(1)
Supply electrical power (Ref 24-22-00/201).
S 864-009
(2)
Open this circuit breaker and attach a DO-NOT-CLOSE tag:
(a)
P6-2 Circuit Breaker Panel
1) ALT TE FLAP DRIVE AC
S 864-007
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-71
ALL ú ú 02 Page 403 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 864-010
(3)
Pressurize hydraulic system B (Ref 27-81-00/201).
S 864-011
(4)
Put the flap control lever to the FLAP UP detent.
S 864-025
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING
_______ EDGE CONTROL SURFACES. THE LEADING EDGE CONTROL SURFACES WILL EXTEND. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
CAUTION: MAKE SURE THAT THE INBOARD FAN DUCT COWL AND THRUST REVERSERS
_______ ARE CLOSED OR REMOVED BEFORE YOU EXTEND THE LEADING EDGE FLAPS. THERE IS NOT SUFFICIENT CLEARANCE FOR THE FLAPS TO EXTEND IF THE COWL AND THE THRUST REVERSERS ARE IN THE OPEN POSITION. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
CAUTION: MAKE SURE THE ALTERNATE FLAP DRIVE UNIT IS KEPT TO A LIMIT OF
_______ 10 MINUTES OPERATION AND 25 MINUTES OFF. THIS WILL PREVENT THE ALTERNATE FLAP DRIVE UNIT FROM DAMAGE.
(5)
Put the alternate flap arm switch to ARM.
S 864-028
(6)
Put the alternate flap control switch to DOWN.
(a)
Make sure the leading edge flaps and slats fully extend.
S 864-012
(7)
Put the alternate flap control switch to OFF.
S 864-013
(8)
Put the alternate flap arm switch to OFF.
(a)
Make sure the leading edge flaps and slats fully retract.
S 874-014
(9)
Operate the leading edge flaps and slats to bleed the standby hydraulic system:
(a)
Put the alternate flap arm switch to ARM.
(b)
Put the alternate flap drive switch to DOWN.
(c)
Make sure the leading edge flaps and slats fully extend.
(d)
Put the alternate flap control switch to OFF.
(e)
Put the alternate flap arm switch to OFF.
(f)
Make sure the leading edge flaps and slats fully retract.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-71
ALL ú ú 02 Page 404 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 794-015
(10)
Make sure the hydraulic fittings of the flow-limiting valve have no leaks.
S 864-016
(11)
Remove the DO-NOT-CLOSE tag and close this circuit breaker:
(a)
P6-2 Circuit Breaker Panel
1) ALT TE FLAP DRIVE AC
S 864-017
(12)
Release the pressure from the hydraulic system B (Ref 27-81-00/201).
S 434-018
(13)
Install a lockwire on the alternate flap arm switch.
S 864-019
(14)
Remove electrical power (Ref 24-22-00/201).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(99)
