EQUIPMENT.
(4)
Install the leading edge flap actuator locks on all the flaps but the flap you will adjust (AMM 27-81-00/201).
S 215-056
(5)
On the outboard flap, make sure the flap nose touches the pads on the flap panel (Fig. 503).
(a)
Adjust if it is necessary: 1) Make sure that the center-to-center lengths of the flap
nose links are as shown.
2) Disconnect the links from the cranks.
3) Adjust as it is necessary.
4) Tighten the adjustment nuts.
5) Install the lockwire.
6) Connect the links to the cranks.
7) Tighten the nuts to 5-10 pound-inches.
8) Install the cotter pins.
9) Disconnect the flap nose rods from the flap nose.
10) Adjust the length to get the flap nose to firmly touch the
pad. 11) Tighten the adjustment nuts. 12) Install the lockwire. 13) Connect the flap nose rods to the flap nose. 14) Tighten the nuts to 5-10 pound-inches. 15) Install the cotter pins.
S 425-057
(6) Disconnect the actuator from the flap panel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 01 Page 532 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 865-058
(7)
Manually retract the flap.
S 215-059
(8)
Make sure there is clearance between the flap nose, structure, actuator and equipment.
S 215-060
(9)
On the inboard flap, make sure there is clearance between the flap nose and the fuel boost pump, the upstop and the inner surface of the flap panel.
NOTE: To do a check for clearances at the inboard flap nose, apply
____ modeling clay. Do a check of the impressions to find the clearances.
(a) Adjust the adjustable link if it is necessary:
1) Make the adjustable link longer to increase the clearance between the flap nose and the fuel boost pump.
NOTE: With the flap nose link disconnected and the flap
____ nose folded back, the clearance between the flap nose and the crank must be 0.01 |0.01 inch.
a) Make sure the flap nose touches the flap on extension. b) Make sure there is a clearance between the flap nose and the fuel boost pump on retraction. c) Adjust the adjustable link again if there is not
sufficient clearance. d) Extend the flap. e) Temporarily connect the actuator to the flap. f) Make sure that the flap nose touches the flap. g) Tighten the adjustment nuts. h) Install a lockwire on the adjustment nut. i) Connect the flap nose link and adjustable link to the
crank. j) Tighten the nuts to 5-10 pound-inches.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 02 Page 533 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
k) Install the cotter pin.
l) Remove the bolt.
m) Hold the actuator.
S 225-125
(10)
Do a check for clearance between the inboard end of the flap nose and the retainer fasteners on the seal support.
(a)
Make sure there is a 0.02 inch minimum clearance between the retainer fasteners and the flap nose.
S 865-061
(11)
Retract the flap panel.
S 215-062
(12)
Make sure that the seal depressor on the flap touches the full length of the bulb seal in the wing.
S 865-063
(13)
Extend the flap.
S 225-064
(14)
Make sure there is an opening of 0.08 inch minimum between the depressor and the structure.
(a)
Adjust the seal depressor position if it is necessary (Fig. 504).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(39)
