S 865-009
(10)
Put the flap control lever to the FLAP UP detent.
(a)
While the flaps and slats retract, make sure the amber TRANSIT lights come on.
(b)
Do these checks when the flaps and slats are fully retracted: 1) Make sure the amber TRANSIT lights go off.
NOTE: The amber indicator lights can come on if the slats
____ are extended and hydraulic pressure is removed. The lights must operate as specified when you supply hydraulic power to system B.
2) Make sure no green lights come on.
D. Put the Airplane Back to Its Usual Condition
S 865-001
(1)
Release pressure from hydraulic system B (Ref 27-81-00/201).
(2)
Remove electrical power (Ref 24-22-00/201).
S 865-002
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-88-11
ALL ú ú 01 Page 503 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLAPS 10-DEGREE SWITCH - REMOVAL/INSTALLATION
_____________________________________________
1. General_______
A. There are two tasks in this procedure. There is a task for the removal and a task for the installation of the flaps 10-degree switch (S584).
TASK 27-88-21-004-001
2. Flaps 10-Degree Switch Removal______________________________
A. Access
(1) Location Zone
217 Main Wheel Well, RH
FLAP FLAPS 10-DEGREE
CONTROL SWITCH, S584
UNIT SEE A
SWITCH RETAINING
COVER NUTS
SEE B
ROLLER GUIDE PIN
(EXAMPLE)
FWD INBD
INBD
A B
Flaps 10-degree Switch Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-88-21
ALL ú ú 02 Page 401 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
B. Special Tools and Equipment
(1)
F80197-5 Wrench Set
C.
Procedure
S 864-002
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6-2 Circuit Breaker Panel
1) FLAP SHUTOFF VALVE
S 024-011
(2)
Use the wrench set to remove the flaps 10-degree switch.
S 024-004
(3)
Remove the switch (Fig. 401):
(a)
Remove the switch cover from the flap control unit.
(b)
Remove the switch leads for the connector.
(c)
Remove the pin to release the roller guide.
(d)
Remove the retainer nut from the switch.
(e)
Remove the switch from the flap control unit.
TASK 27-88-21-404-003
3. Flaps 10-Degree Switch Installation___________________________________
A. References
(1)
27-88-21/501, Flaps 10-Degree Switch
B.
Access
(1)
Location Zone
217 Main Wheel Well, RH
C.
Special Tools and Equipment
(1)
F80197-5 Wrench Set
D.
Procedure
S 494-009
(1)
Use the wrench set to install the flaps 10-degree switch.
S 424-005
(2)
Install the switch (Fig. 401):
(a)
Put the switch in the flap control unit.
(b)
Install the retainer nut and roller guide.
(c)
Install the pin.
(d)
Install the switch leads in the connector.
(e)
Connect the switch leads to the receptacle.
(f)
Install the switch cover.
S 864-006
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6-2 Circuit Breaker Panel
1) FLAP SHUTOFF VALVE
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(161)
