S 014-048

 (5)  
Remove the access panels.

 E.
Procedure

 S 024-049
 (1)  
Remove the auxiliary track seal door for the slats 2, 3, 4 and 5 (Detail A and B):

 (a)  
Hold the seal door while you remove the bolts that attach the hinge assembly to the fixed leading edge.

 (b)  
Remove the seal door.

 S 024-050
 (2)  
Remove the auxiliary track seal door for the slats 1 and 6 (middle and inboard positions) (Detail C):

 (a)  
Remove the nut, bolt, spacer, and washers that attach each spring to the seal door.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-51
 ALL  ú ú 02 Page 413 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Move the seal door aft along the seal guide and spacer until it is clear.
 TASK 27-81-51-404-052
 7.  Auxiliary Track Seal Door Installation______________________________________
 A.  Special Tools and Equipment
 (1)  
C27012-1 - Leading Edge Slat Actuator Lockout Set

 B.  
References

 (1)  
27-81-00/201, Leading Edge Flap and Slat Control System

 C.  
Access

 (1)  
Location Zone 101 Control Cabin, LH 102 Control Cabin, RH 302 Wing Outboard Leading Edge with Slats, LH 402 Wing Outboard Leading Edge with Slats, RH

 (2)  
Access Panels
 6244 Slat Access Panel, LH
 6245 Slat Access Panel, LH
 6248 Slat Access Panel, LH
 6252 Slat Access Panel, LH
 6255 Slat Access Panel, LH
 6260 Slat Access Panel, LH
 6262 Slat Access Panel, LH
 6544 Slat Access Panel, RH
 6545 Slat Access Panel, RH
 6548 Slat Access Panel, RH
 6552 Slat Access Panel, RH
 6555 Slat Access Panel, RH
 6560 Slat Access Panel, RH
 6562 Slat Access Panel, RH

 D.  
Procedure

 S 424-053
 (1)  
Install the auxiliary track seal door for slats 2, 3, 4 and 5 (Detail A and B):

 (a)  
Put the seal door and the shims in the correct positions.

 1)  If it is necessary, remove a lamination from the shims to attach the seal door correctly to the top panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-51
 ALL  ú ú 03 Page 414 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2)  Apply primer to the shims before the last installation.
 (b)  Install the bolts that attach the seal door hinge assembly to the fixed leading edge.
 S 424-054
 (2)  
Install the auxiliary track seal door for the slats 1 and 6 (mid and inboard positions) (Detail C):

 (a)  
Install the torsion springs:

 1)  Attach each spring to the seal door guide and spacer with the nut, bolt, spacer and washers.

 (b)  
Move the door in the seal guide and spacer.

 (c)  
Attach each spring to the seal door with the nut, bolt, spacer, dimpled washer, and washers.

 (d)  
Make sure there is a 0.08 inch minimum overlap between the top of the skin cutout and the top edge of the seal door.

 NOTE: The seal doors must move freely.
____
 E.  Put the Airplane Back to Its Usual Condition
 S 414-056
 (1)  Install the access panels.
 S 084-057
 WARNING: CAREFULLY REMOVE THE LEADING EDGE SLAT ACTUATOR LOCKOUT SET.
_______ THE LEADING EDGE SLATS CAN MOVE QUICKLY IF YOU DO NOT REMOVE THE LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Remove the leading edge slat actuator lockout set from the actuators of the leading edge slats (Ref 27-81-00/201).

 S 864-058

 (3)  
Put the flap control lever to the FLAP UP detent to fully retract the leading edge devices.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(95)