曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (3)  S 432-031Install the sleeve in the support plate recess.
 (4)  S 432-032Push the seal door shaft through the inboard support plate, inboard sleeve, lever assembly, outboard sleeve, and outboard support plate.
 (5)  S 432-033Put the collar on the shaft.
 (6)  S 432-034Install the bolt through the collar and the shaft.
 (7)  S 432-035Tighten the bolt to 20-25 pound-inches.
 (8)  S 862-036Put a load on the spring (for the inboard and outboard spring): (a) Remove the three bolts from the support plate and rib. (b) With the lever on the seal door stop and no tension on the spring, install a steel pin in the support plate (Detail C). (c) Use an open end wrench on the support plate, move the support plate in the direction of the preload arrow (20 degrees approximately). (d) Engage the spring in the stop bracket. (e) Remove the steel pin from the support plate. (f) Turn the support plate to permit the installation of the 3/16-inch bolts. (g) Tighten the bolts to 20-25 pound-inches.
 (9)  S 432-042Connect the link assembly to the lever assembly.
 S 432-043

 (10)
 Tighten the bolt to 50-75 pound-inches. S 862-044

 (11)
 Manually put the seal door aft of the Krueger flap. S 432-045

 (12)
 Install the cam roller on the seal door. S 862-037

 (13)
 Tighten the bolt to 60-85 pound-inches.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-14
 ALL  ú ú 01 Page 209 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 082-052
 WARNING:_______CAREFULLY REMOVE THE LEADING EDGE FLAP ACTUATOR LOCKS. THE LEADING EDGE FLAPS CAN MOVE QUICKLY IF YOU DO NOT REMOVE THE LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (14)
 Remove the leading edge flap actuator locks from the actuators of the leading edge flaps (Ref 27-81-00/201).

 S 862-038

 (15)
 Pressurize hydraulic system B (Ref 27-81-00/201).

 S 862-039

 (16)
 Move the flap control lever to the FLAP UP detent.

 S 862-040

 (17)
 Release the pressure from hydraulic system B (Ref 27-81-00/201).

 S 822-041

 (18)
 Adjust the seal door.

 TASK 27-81-14-822-023
 6.  Seal Door Adjustment____________________
 A. Special Tools and Equipment
 (1)
F80048-84, -89, -90 - Leading Edge Flap Actuator Lock

 B.
Standard Tools and Equipment

 (1)
Steel pin - 1/4 inch diameter x 1-1/2 inch

 C.
Consumable Materials

 (1)
C00259 Enamel - Primer, BMS 10-11, Type 1

 D.
References

 (1)
27-81-00/201, Leading Edge Flap and Slat Control System

 (2)
27-81-00/501, Leading Edge Flap and Slat Control System

 E.
Access

 (1)  
Location Zone 101 Control Cabin, LH 102 Control Cabin, RH 302 Wing Outboard Leading Edge with Slats, LH 303 Wing Inboard Leading Edge with Slats, LH 402 Wing Outboard Leading Edge with Slats, RH 403 Wing Inboard Leading Edge with Slats, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-14
 ALL  ú ú 01 Page 210 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 F.  Procedure
 S 862-050
 (1)  
Make sure the adjustment of the Krueger flaps is correct
 (Ref 27-81-00/501).

 S 822-022

 (2)  
Adjust the seal door (Fig. 201):

 (a)  
Pressurize hydraulic system B (Ref 27-81-00/201).

 (b)  
Move the flap control lever to the 1-unit detent to extend the leading edge flaps.

 (c)  
Remove the cam roller (Detail D).

 (d)  
Remove the cam shim from below the cam, found on the outboard end of the outboard Krueger flap.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(65)