27-81-41
 ú  ALL  ú
 ú ú  ú 02.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 404Nov 12/01 

A
737-300/400/500MAINTENANCE MANUAL
 S 494-026
 WARNING:_______ YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
 THE LEADING EDGE FLAP AND SLAT LOCKS.  THE LEADING EDGE FLAPS
 AND SLATS CAN MOVE QUICKLY IF YOU DO NOT INSTALL THE LOCKS
 CORRECTLY.  THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO

 EQUIPMENT.
 (4)  
Install the leading edge slat locks on the adjacent leading edge slats (Ref 27-81-00/201).

 S 424-005

 (5)  
Remove the slat actuator door from the actuator. S 014-040

 (6)  
Remove the seal and access panel from the slat at the actuator rod end.

 S 864-042

 (7)  
Move the flap control lever to the 5-unit detent.

 S 864-028 WARNING: MAKE SURE TO DEPRESSURIZE THE HYDRAULIC SYSTEM WHEN YOU DO
_______ ADJUSTMENTS. FAILURE TO DEPRESSURIZE THE HYDRAULIC SYSTEM CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (8)  Release the pressure from hydraulic system B when the leading edge slat is half between the fully extended and the intermediate positions (Ref 27-81-00/201).
 NOTE: Retraction of the slat removes the load from the actuator rod
____ end attach bolt.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-41
 ú  ALL  ú
 ú ú  ú 02.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 405Nov 12/01 

A
737-300/400/500MAINTENANCE MANUAL
 S 864-046
 WARNING: MAKE SURE THAT YOU HOLD THE LEADING EDGE SLAT IN ITS POSITION.
_______ THE LEADING EDGE SLAT CAN FALL TO THE FULL EXTEND POSITION. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (9)  
Hold the slat in position and remove the rod end attach bolt that connects the slat to the slat structure.

 (a)  
Remove the nut and washers from the bolt.

 (b)  
Move the bolt out until the bolt head touches the slat structure.

 (c)  
Move the bushing out until the bushing contacts the bolt head flange.

 (d)  
Remove the bolt and bushing.

 S 864-047
 (10)
 Let the slat move to the full extend position.

 S 864-006

 (11)
 Pressurize hydraulic system B (Ref 27-81-00/201).

 S 214-048

 (12)
 Monitor the slat actuator retract to the intermediate extend position.

 S 864-008

 (13)
 Release the pressure from hydraulic system B just before the slat actuator is in the intermediate extend position (Ref 27-81-00/201).

 S 864-009

 (14)
 Release the pressure from the standby system (Ref 27-81-00/201).

 S 864-010

 (15)
 Release the pressure from hydraulic system B reservoir
 (Ref 29-09-00/201).

 E.
Remove the Leading Edge Slat Actuator

 S 024-023
 (1)  
Remove the actuator:

 (a)  
Remove the bolts from the inboard rib at the actuator.

 (b)  
Remove the rib lower cord.

 (c)  
Remove the clamps that attach the hydraulic lines to the wing structure.

 (d)  
Tag all the hydraulic lines and ports for correct replacement.

 (e)  
Disconnect the hydraulic lines from the swivel joints.

 (f)  
Install the plugs in the hydraulic lines.

 (g)  
Seal all the ports with the caps.

 (h)  
Disconnect the actuator from the support fitting in the wing.

 (i)  
Remove the actuator.

 (j)  
Disconnect the hydraulic lines from the actuator.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-41
 ALL  ú ú 06 Page 406 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(80)