(b)  
Put the speed brake lever in the UP position to lift the spoilers.

 (c)  
Make sure that the ground spoilers are up 60 |2 degrees from the fully retracted position.

 (d)  
Make sure that the spoilers No. 0 and 9 align in the limit of 2 degrees.

 (e)  
Make sure that the spoilers No. 1 and 8 align in the limit of 2 degrees.

 (f)  
Put the speed brake lever in the DOWN position to lower the spoilers.

 (g)  
Make sure that the spoilers are in the fully down position.

 (h)  
Remove the control surface protractor and the stand from the spoilers.

 E.
Put the Airplane Back to Its Usual Condition

 (1)  
Remove the system A hydraulic power (Ref 27-62-00/201).

 (2)  
Put the SPOILER A and B switches in the ON position.

 (3)  
Remove the electrical power (Ref 24-22-00/201).

 S 865-019
 S 865-020
 S 865-021
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-94
 ALL  ú ú 02 Page 505 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 NO. 0, 1, 8 AND 9 GROUND SPOILER ACTUATOR - INSPECTION/CHECK
____________________________________________________________
 1.  General_______
 A.  There is one task in this procedure, an inspection of the ground spoiler actuator. To do the inspection you measure the diameters of the bushings that attach the actuator to the spoiler panel.
 TASK 27-62-94-226-001
 2.  No. 0, 1, 8 and 9 Ground Spoiler Actuator Inspection____________________________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0 to 1 inch

 B.  
References

 (1)  
27-62-94/401, No. 0, 1, 8 and 9 Ground Spoiler Actuator

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Inboard Flaps and Spoiler

 D.  
Procedure

 S 026-002
 (1)  
Remove the ground spoiler actuator (Ref 27-62-94/401).

 S 226-003

 (2)
Measure the bushings for the ground spoiler actuator (Fig. 601):

 (a)  
Remove the bushings from the rod end.

 (b)  
Use a micrometer to measure the bushings.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Replace the bushings that are not in the tolerance.

 (e)  
Install the bushings.

 (3)  
Install the ground spoiler actuator (Ref 27-62-94/401).

 S 426-004
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-94
 ALL  ú ú 01 Page 601 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
1. BUSHING/BUSHING
SPOILER ACTUATOR (EXAMPLE) NO. 0 GROUND 1  8  9 
SEE  A  A-A 
A  SPOILER GROUND 
A 

OUTBD 
ACTUATOR  FWD 
A GROUND SPOILER ACTUATOR (EXAMPLE) 
NO. INDEX  PART NAME  DIM.  MAXMIN DESIGN LIMITS DIAMETER  PER-MITTED WEAR DIM. ANCE WEAR LIMITS CLEAR-MAX DIA  PARTWORN REPLACE  PART WORN REPAIR  INSTR REPAIR 
1  BUSHING (PLAIN) BUSHING (FLANGED)  ID OD  0.7480 0.7500  0.7490 0.7515  0.7465 0.7540  0.0055  X

No. 0, 1, 8 and 9 Ground Spoiler Actuator Wear Limits
Figure 601

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-94
 ALL  ú ú 01 Page 602 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 LEADING EDGE FLAP AND SLAT CONTROL SYSTEM - DESCRIPTION AND OPERATION
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(12)