B.
Special Tools and Equipment
(1)
F80049-12 - Flight Controls Lock Assembly
C.
References
(1)
AMM 24-22-00/201, Manual Control
D.
Access
(1)
Location Zone
101 Control Cabin, LH
102 Control Cabin, RH
302 Outboard Leading Edge with Slats, LH
303 Inboard Leading Edge with Slats, LH
402 Outboard Leading Edge with Slats, LH
403 Inborad Leading Edge with Slats, RH
E.
Procedure
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 02 Page 207 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 862-050
WARNING: MAKE SURE THE INBOARD AND OUTBOARD FAN DUCT COWLS AND THE
_______ THRUST REVERSERS ARE CLOSED OR REMOVED IF YOU NEED TO EXTEND THE LEADING EDGE FLAPS AND SLATS. THERE IS NOT SUFFICIENT CLEARANCE FOR THE LEADING EDGE FLAPS AND SLATS TO EXTEND IF THE INBOARD AND OUTBOARD FAN DUCT COWLS AND THRUST REVERSERS ARE IN THE OPEN (MAINTENANCE) POSITION. THIS CAN CAUSE DAMAGE TO EQUIPMENT.
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING
_______ EDGE FLAPS AND SLATS. IF YOU MOTOR THE ENGINES IT CAN CAUSE EXTENSION OF THE LEADING EDGE FLAPS AND SLATS BECAUSE OF PRESSURIZATION OF HYDRAULIC SYSTEMS A OR B. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT. PUT A "DO NOT DRY MOTOR ENGINE WITH THE THRUST REVERSER COWLS OPEN" PLACARD ON THE ENGINE START SWITCH."
WARNING: MAKE SURE LEADING EDGE FLAPS, LEADING EDGE SLATS, AND TRAILING
_______ EDGE FLAPS ARE IN THE FULL (UP) RETRACTED POSITION AND THE POWER TRANSFER UNIT, HYDRAULIC SYSTEM B, AND THE STANDBY SYSTEMS ARE DEACTIVATED BEFORE YOU MOTOR THE ENGINES. DO NOT MOTOR THE ENGINES WITH THE TRAILING EDGE FLAP EXTENDED. IF YOU DO, THE SLATS WILL BE ACTIVATED AND EXTENDED BY HYDRAULIC POWER ORIGINATED FROM THE (HYDRAULIC SYSTEM B) ENGINE DRIVEN PUMP AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
WARNING: MAKE SURE THE POSITION OF THE FLAPS AND SLATS AGREES WITH THE
_______ POSITION OF THE FLAP CONTROL LEVER. WHEN YOU PRESSURIZE THE HYDRAULIC SYSTEM B, THE FLAPS AND SLATS WILL MOVE AUTOMATICALLY TO THE POSITION OF THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1)
Leading Edge Flaps and Slats Deactivation to operate the Trailing Edge Flaps in the alternate (fully electric) mode, and with no hydraulic power systems A, B, or Standby available). Do the steps that follow:
(a)
Put a "DO NOT DRY MOTOR ENGINE WITH THE THRUST REVERSER COWLS OPEN" placard on engine start switch to prevent engine dry motoring with the thrust reverser cowls open, and to prevent uncommanded slat extension caused by (EDP) Engine Driven Pump pressurization of hydraulic system B.
(b)
Make sure the leading edge flaps, leading edge slats, and trailing edge flaps are in the full (UP) retracted position.
(c)
Release the pressure from hydraulic systems A, B, and Standby (AMM 29-09-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-00
ALL ú ú 02 Page 208 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(d) Make sure the lever in the PTU control valve is in the closed position.
NOTE:____ The PTU control valve is found in the
left hand/forward side of the wheel well. Use a flashlight and a mirror when you do the close position check on the PTU control valve.
(e) Open these circuit breakers and attach DO-NOT-CLOSE tags: 1) P6-2 Circuit Breaker Panel a) PTU/LG BYP V CONT 1 b) PTU/LG BYP V CONT 2 2) P6-11 Circuit Breaker Panel a) STBY HYD PUMP NORMAL b) ELEC HYD PUMP SYS B 3) P6-12 Circuit Breaker Panel a) STBY HYD PUMP (ALT)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(23)
