- do a check of the wiring and make sure that there is a ground signal at pin AA/7G and an open circuit at pin AA/7F on the rack connector.
(1) If the pin programming is incorrect:
- repair the aircraft wiring: defective pin
- install the ADIRU2.
(2) If the pin programming is correct:
- do a check of pin AA/3C on the rack connector
- compare the state of the pin with the BARO PORT A SELECT pin programming given in the ASM (Ref. ASM 34-12/02).
(a) If the pin programming is correct:
- install a new ADIRU2 (Ref. AMM TASK 34-12-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-210, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B231
301-399, 401-499, Aug 01/05 CES
(b) If the pin programming is incorrect:
- repair the wiring BARO PORT A SELECT pin programming of the ADIRU2: pin AA/3C.
- install the ADIRU2.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-210, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B232
301-399, 401-499, Aug 01/05 CES
Failure of the ADR3 Baro-Source Pin-Programming
1. Possible Causes
_______________
- ADIRU-3 (1FP3)
- aircraft wiring
- wiring BARO PORT A SELECT pin programming of the ADIRU3
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-13-00-740-002 INTERFACE TEST of the ADR
ASM 34-12/03
3. Fault Confirmation
__________________
A. Test Do the Interface test of the ADR (system 3) (Ref. AMM TASK 34-13-00-740-002).
4. Fault Isolation
_______________
A. If the test gives the maintenance message WRG: BARO SOURCE SELECT PIN PROG:
- remove the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001)
- do a check of the wiring and make sure that there is a ground signal at pin AA/7G and an open circuit at pin AA/7F on the rack connector.
(1) If the pin programming is incorrect:
- repair the aircraft wiring: defective pin
- install the ADIRU3.
(2) If the pin programming is correct:
- do a check of pin AA/3C on the rack connector
- compare the state of the pin with the BARO PORT A SELECT pin programming given in the ASM (Ref. ASM 34-12/03).
(a) If the pin programming is correct:
- install a new ADIRU3 (Ref. AMM TASK 34-12-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-210, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B233
301-399, 401-499, Aug 01/05 CES
(b) If the pin programming is incorrect:
- repair the wiring BARO PORT A SELECT pin programming of the ADIRU3: pin AA/3C.
- install the ADIRU3.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-210, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B234
301-399, 401-499, Aug 01/05 CES
Failure of the ADR1 AOA Average-Unique Pin-Programming
1. Possible Causes
_______________
- ADIRU-1 (1FP1)
- wiring AOA UNIQUE pin programming of the ADIRU1
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(5)
