TASK 34-36-00-810-845
 Failure of the MMR2

 1. Possible Causes
_______________
 - MMR-2 (40RT2)

 - wiring between the MMR receiver 2 and the first ground terminal

 - wiring between the circuit breaker (42RT2) and the MMR receiver 2

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 34-36-00-740-003 BITE Test of the MMR
 AMM 34-36-31-000-002 Removal of the Multi Mode Receiver (40RT1, 40RT2)
 AMM 34-36-31-400-002 Installation of the Multi Mode Receiver (40RT1,

 40RT2)
 ASM 34-36/01

 3. Fault Confirmation
__________________ **ON A/C ALL R Post SB 34-1147 For A/C 001-004,051-060,
 A. Test Do the BITE test of the MMR2 (Ref. AMM TASK 34-36-00-740-003).

 4. Fault Isolation
_______________
 **ON A/C ALL
R  Post SB 34-1147 For A/C 001-004,051-060, Post SB 34-1184 For A/C 001-004,
R  Post SB 34-1186 For A/C 001-049,101-101,
 A. If the test gives the maintenance message MMR2 (40RT2):
 - remove the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002).

 - do a check for a ground signal at pin AC/7 of the MMR receiver 2.

 (1) If there is no ground signal:

 - do a check and repair the wiring between the MMR receiver 2 and the first ground terminal: pin AC/7 of the MMR receiver 2 (Ref. ASM 34-36/01)

 - install the MMR receiver 2 (Ref. AMM TASK 34-36-31-400-002).

 (2) If there is a ground signal:

 - do a check for 115VAC between pins AC/7 and AC/9 of the MMR receiver 2.
 (a) If there is no 115VAC:

 - do a check and repair the wiring between the circuit breaker (42RT2) and the MMR receiver 2: pin AC/9 of the MMR receiver 2 (Ref. ASM 34-36/01)

 - install the MMR receiver 2.

 (b) If there is 115VAC:

 - install a new MMR receiver 2.
 **ON A/C ALL
R  Post SB 34-1147 For A/C 001-004,051-060,
 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-36-00∞∞∞∞∞∞∞∞∞∞Page 289
 May 01/05 CES TASK 34-36-00-810-846

 Loss of the ILS Localizer Antenna Signal
 1. Possible Causes
_______________
 - MMR-1 (40RT1)

 - MMR-2 (40RT2)

 - ANTENNA-LOCALIZER 1/2 (3RT)

 - coaxial cable between the MMR1 and the localizer antenna 1/2 (3RT)

 - coaxial cable between the MMR2 and the localizer antenna 1/2 (3RT)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 34-36-00-740-003 BITE Test of the MMR
 AMM 34-36-11-000-001 Removal of the Localizer Antenna (3RT)
 AMM 34-36-11-400-001 Installation of the Localizer Antenna (3RT)
 AMM 34-36-31-000-002 Removal of the Multi Mode Receiver (40RT1, 40RT2)
 AMM 34-36-31-400-002 Installation of the Multi Mode Receiver (40RT1,

 40RT2)
 ASM 34-36/01

 3. Fault Confirmation
__________________
 **ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060,
 A. Test Do the BITE test of the MMR1 (Ref. AMM TASK 34-36-00-740-003).

 4. Fault Isolation
_______________
 **ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060,
 A. If the test of the MMR1 only gives the maintenance message
 LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR1(40RT1):

 - swap the MMR-1 (40RT1) and the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref. AMM TASK 34-36-31-400-002)

 - do the BITE test of the MMR1 (Ref. AMM TASK 34-36-00-740-003).

 (1) If the test of the MMR1 gives the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR1(40RT1):

 - remove the MMR1

 - remove the localizer antenna 1/2 (Ref. AMM TASK 34-36-11-000-001)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(127)