40RT2)
3. Fault Confirmation
__________________ **ON A/C ALL R Post SB 34-1147 For A/C 001-004,051-060,
A. Test Do the BITE test of the MMR2 (Ref. AMM TASK 34-36-00-740-003).
**ON A/C ALL
4. Fault Isolation
_______________ **ON A/C ALL R Post SB 34-1147 For A/C 001-004,051-060,
A. If the test gives the maintenance message MMR2 (40RT2):
- replace the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref. AMM TASK 34-36-31-400-002).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-36-00∞∞∞∞∞∞∞∞∞∞Page 285
May 01/05 CES TASK 34-36-00-810-844
Loss of the GPS Data in the MMR2
1. Possible Causes
_______________
R
- MMR-2 (40RT2) R - ANTENNA-GPS ACTIVE, 2 (43RT2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 20-28-00-912-003 Electrical Bonding of Electrical Connectors AMM 34-36-00-740-003 BITE Test of the MMR AMM 34-36-16-000-001 Removal of the GPS Active Antenna (43RT1, 43RT2) AMM 34-36-16-400-001 Installation of the GPS Active Antenna (43RT1, 43RT2)
with Teflon Seal AMM 34-36-31-000-002 Removal of the Multi Mode Receiver (40RT1, 40RT2) AMM 34-36-31-400-002 Installation of the Multi Mode Receiver (40RT1,
40RT2) R SRM 517400 P.Block001
3. Fault Confirmation
__________________
**ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060,
A. Test Do the BITE test of the MMR2 (Ref. AMM TASK 34-36-00-740-003).
**ON A/C ALL
4. Fault Isolation
_______________
R **ON A/C 051-099,
R A. If the test gives the maintenance message MMR2 (40RT2):
R - replace the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref.
R AMM TASK 34-36-31-400-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-36-00∞∞∞∞∞∞∞∞∞∞Page 286
May 01/05 CESR **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
Post SB 34-1147 For A/C 001-004,
Post SB 34-1184 For A/C 001-004,
A. If the test gives the maintenance message MMR2(40RT2):
- on the MCDU, push the line key adjacent to the maintenance message class number to get access to the trouble shooting data and read the related fault code.
- make a record of the fault code.
NOTE : Use only the second and third digits of the fault code(s).
____
(1) If the trouble shooting data give the fault code XA7X or XA8X:
- remove the MMR2 (Ref. AMM TASK 34-36-31-000-002)
- remove the GPS antenna 2 (Ref. AMM TASK 34-36-16-000-001)
- make sure that there is no moisture and/or corrosion on the coaxial cable of the GPS antenna 2
- if you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 517400 P.Block001) for types, inspection, removal and corrosion protection
- make sure that there is continuity on the coaxial cable of the GPS antenna 2 (Ref. AMM TASK 20-28-00-912-003)
- replace the coaxial cable if necessary
- make sure that there is discontinuity between the core and shield of the coaxial cable of the GPS antenna 2
- repair if necessary.
(a) If the fault stops:
- install the MMR2 (Ref. AMM TASK 34-36-31-400-002)
- install the GPS antenna 2 (Ref. AMM TASK 34-36-16-400-001).
(b) If the fault continues:
- install a new ANTENNA-GPS ACTIVE, 2 (43RT2) (Ref. AMM TASK 34-36-16-400-001) ANTENNA-GPS ACTIVE, 2
- install the MMR2 (Ref. AMM TASK 34-36-31-400-002).
(2) If the trouble shooting data do not give the fault code XA7X or XA8X:
- replace the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref. AMM TASK 34-36-31-400-002).
**ON A/C ALL
Post SB 34-1147 For A/C 001-004,051-060,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(126)
