- make sure that there is continuity on the coaxial cable between the MMR1 and the localizer antenna 1/2 (3RT) (Ref. ASM 34-36/01)
- replace the coaxial cable if necessary
- make sure that there is discontinuity between the core and the shield of the coaxial cable
- repair if necessary
- install the MMR1
- install the localizer antenna 1/2 (3RT) (Ref. AMM TASK 34-36-11-400-001).
(2) If the test of the MMR1 does not give the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR1(40RT1):
- replace the MMR that you installed on side 2.
B. If the test of the MMR2 only gives the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR2(40RT2):
- swap the MMR-1 (40RT1) and the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref. AMM TASK 34-36-31-400-002)
- do the BITE test of the MMR2 (Ref. AMM TASK 34-36-00-740-003).
(1) If the test of the MMR2 gives the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR2(40RT2):
- remove the MMR2
- remove the localizer antenna 1/2 (Ref. AMM TASK 34-36-11-000-001)
- make sure that there is continuity on the coaxial cable between the MMR2 and the localizer antenna 1/2 (3RT) (Ref. ASM 34-36/01)
- replace the coaxial cable if necessary
- make sure that there is discontinuity between the core and the shield of the coaxial cable
- repair if necessary
- install the MMR2
- install the localizer antenna 1/2 (3RT) (Ref. AMM TASK 34-36-11-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-36-00∞∞∞∞∞∞∞∞∞∞Page 291
May 01/05 CES
(2) If the test of the MMR2 does not give the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR2(40RT2):
- replace the MMR that you installed on side 1.
C. If the test of the MMR1 gives the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR1(40RT1) and if the test of the MMR2 gives the maintenance message LOCALIZER ANTENNA (3RT)/COAX CABLE/MMR2(40RT2):
- replace the ANTENNA-LOCALIZER 1/2 (3RT) (Ref. AMM TASK 34-36-11-000-001) and (Ref. AMM TASK 34-36-11-400-001).
D. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-36-00∞∞∞∞∞∞∞∞∞∞Page 292
May 01/05R
CES TASK 34-36-00-810-847
Loss of the ILS Glide/Slope Antenna Signal
1. Possible Causes
_______________
- MMR-1 (40RT1)
- MMR-2 (40RT2)
- ANTENNA-GLIDE/SLOPE 1/2 (4RT)
- coaxial cable between the MMR1 and the glide antenna 1/2 (4RT)
- coaxial cable between the MMR2 and the glide antenna 1/2 (4RT)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 34-36-00-740-002 BITE Test of the ILS
AMM 34-36-00-740-003 BITE Test of the MMR
AMM 34-36-11-000-001 Removal of the Localizer Antenna (3RT)
AMM 34-36-11-400-001 Installation of the Localizer Antenna (3RT)
AMM 34-36-18-000-001 Removal of the Glide/Slope Antenna (4RT)
AMM 34-36-18-400-001 Installation of the Glide/Slope Antenna (4RT)
AMM 34-36-31-000-002 Removal of the Multi Mode Receiver (40RT1, 40RT2)
AMM 34-36-31-400-002 Installation of the Multi Mode Receiver (40RT1,
40RT2)
ASM 34-36/01
3. Fault Confirmation
__________________
**ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060,
A. Test Do the BITE test of the MMR1 (Ref. AMM TASK 34-36-00-740-002).
4. Fault Isolation
_______________
**ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060,
A. If the test of the MMR1 only gives the maintenance message
GLIDE ANTENNA (4RT)/COAX CABLE/MMR1(40RT1):
- swap the MMR-1 (40RT1) and the MMR-2 (40RT2) (Ref. AMM TASK 34-36-31-000-002) and (Ref. AMM TASK 34-36-31-400-002)
- do the BITE test of the MMR1 (Ref. AMM TASK 34-36-00-740-003).
(1) If the test of the MMR1 gives the maintenance message GLIDE ANTENNA (4RT)/COAX CABLE/MMR1(40RT1):
- remove the MMR1
- remove the glide antenna 1/2 (Ref. AMM TASK 34-36-18-000-001) 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(128)
