R Parallel Splices - P/N Characteristics NSA936808
R Figure 004
20-43-12 Page 7
R Parallel Splices - Crimping and Shrinking Tools R NSA936808 R Figure 005
20-43-12 Page 8
R Parallel Splices - Examples of Uses of Compensation Sleeves R NSA936808 R Figure 006
20-43-12 Page 920-43-12 Page 10
R - Move the two handles together or apply pressure to perform the
R crimping operation. Make sure complete crimping is obtained
R (ratchet release or automatic opening of dies).
R - Remove the crimped assembly.
R - Make sure that the connection is in the correct condition and that
R :
R .The cable insulator does not penetrate into the splice barrel.
R .The crimping indents are centered.
R .The stripped conductors do not prodrute excessively (visible
R length < 1.5 mm (0.0590 in.)).
R - If necessary, shrink the compensation sleeve(s).
R - Slide the insulation sleeve "B" in position and shrink it.
_____________________________________________
CRIMP END SPLICES - DESCRIPTION AND OPERATION
_______
1. General
Crimp end splices installed on aircraft have the following codes : NSA936830 1 Conductor crimped end splices E0301 2 Conductors crimped end splices E0543 3 Conductors crimped end splices
___________________2. Crimped end Splices
A. NSA936830
(1) P/N identification NSA936830 | | | - 22|------------- Contact size
------------------------ Standard P/N
(2) P/N characteristics (Ref. Fig. 001)
(a) Temperature Minimum operating temperature is : -55 deg.C (-67.00 deg.F). Maximum operating temperature is : 175 deg.C (347.00 deg.F).
B. E0301
(1)
P/N identification
E0301 -01 | | | ------------- Reference No. | ---------------------- Standard P/N
(2)
P/N characteristics (Ref. Fig. 001)
(a) Temperature Minimum operating temperature is : -55 deg.C (-67.00 deg.F). Maximum operating temperature is :175 deg.C (347.00 deg.F).
C. E0543
(1) P/N identification
20-43-13 Page 1
Crimp End Splices - Contacts Layout
E0301, E0543 and NSA936830
Figure 001
20-43-13 Page 2
E0543 - 01
| |
| ------------- Reference No.
|
---------------------- Standard P/N
(2) P/N characteristics (Ref. Fig. 001)
(a) Temperature Minimum operating temperature is : -55 deg.C (-67.00 deg.F). Maximum operating temperature is : 175 deg.C (347.00 deg.F).
20-43-13 Page 3
________________
3. Connection Table (Ref. Fig. 002)
20-43-13 Page 4
Crimp end Splices - Connection Table
Figure 002
20-43-13 Page 5
__________________________________________
PRESSURE SEALS - DESCRIPTION AND OPERATION
R _______
1. General
This chapter concerns the description, installation and identification of pressure seals used on aircraft.
R A. Grommet type Pressure Seals (Ref. 20-43-41)
B. Compound Filled Pressure Seals (Ref. 20-43-42)
R R C. Adhesive Sealant Pressure Seal (Ref. 20-43-43)
20-43-40 Page 120-43-41 Page 1
________________________________________________________D.T.P. - TYPE PRESSURE SEALS - DESCRIPTION AND OPERATION
R R R R R R R R R R _______1. General The grommet type pressure seals installed on aircraft have the following codes: - ABS0717 Feed Through ABS0834 Feed Through ABS1128 Feed Through E0073 (ex NSA934700) Feed Through - ABS0634 Fireproof ABS0681 Fireproof E0739 Fireproof NSA934501 Fireproof (2 passages) NSA934502 Fireproof (13 passages) NSA934504 Fireproof (4 passages)
__________________________2. Feed Through Pressure Seal
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(7)
