曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (1) Contact arrangement
 (Ref. Fig. 003)
 C. Connection procedure 
R  (Ref. Fig. 004) 
R
R  ____NOTE : Install the connector on the panel before you connect the cables. 
R  - Select the applicable terminals to connect the connectors (Refer 
R  Connection Table paragraph). 
R  (1) For E0354-204 only : 
R  - On the cables to be connected, put heat shrinkable sleeve E0126-09B 
R  or NSA937211-009-E with a length of 70 -5 +5 mm (2.7559 -0.1968 
R  +0.1968 in.) for the insulation of the connector. 
R 
R  - Use a torque screwdriver to attach the terminals to the connector. 
R  TORQUE the screws at the value of : 
R  For diameter 3 : 0.055 m.daN (4.8672 lbf.in) 
R  For diameter 4 : 0.10 m.daN (8.8495 lbf.in) 
R  - Fold the terminals at 90. with a flat-nose pliers (Refer step2).
R  ____NOTE : Do this operation only one time. 
R  - Select the applicable shrinking tool. 
R  - Install the connector insulation from the root of the connector to 
R  the top of the terminals (Refer step3). 
R  - Shrink the sleeve. Make sure that the sleeve length after shrinking 
R  is 50 -5 +5 mm (1.9685 -0.1968 +0.1968 in.). 
R

 

20-44-19 Page 5

 Miscellaneous Circular Connectors - Contact Arrangements E0354 R Figure 003

20-44-19 Page 6

R Miscellaneous Circulars Connectors - Connection Procedure R E0354-204 R Figure 004

20-44-19 Page 720-44-19 Page 8

R  (2) For E0354-301 only : 
R  - On the cables to be connected, put heat shrinkable sleeve E0126-09B 
R  or NSA 937211-009-E with a length of 30 mm (1.1811 in.) for the 
R  insulation of the connector. 
R  - Use a torque screwdriver to attach the terminals to the connector. 
R  TORQUE the screws at the value of : 
R  For diameter 3 : 0.055 m.daN (4.8672 lbf.in) 
R  For diamater 4 : 0.10 m.daN (8.8495 lbf.in) 
R  - Select the applicable shrinking tool. 
R  - Install the connector insulation from the root of the connector to 
R  the top of the terminals (Refer step3). 
R  - Shrink the sleeve. 
R 
R  (3) Only for E0354-302 
R  - Use a torque screwdriver to attach the terminals to the connector. 
R  TORQUE the screws at the value : 
R  for diameter 3 : 0.055 m.daN (4.8672 lbf.in) 
R  for diameter 4 : 0.10 m.daN (8.8495 lbf.in) 
R  - With a spray gun or a brush, apply a very thin coat of PM820 
R  (ASNA4183). 
R  - Let it dry 1 minute before the next operation. 
R  - Apply CAF4 (ASNA4183) on the heads of the screws.
 ____________________________________________4. Miniature Connectors NSA938018 and NSA938019
 A. P/N identification
 NSA938018  A  5  27 S 1
 NSA938019  A  5  27 S 1
 | |  |  | | |
 | |  |  | | ------- Crimp type connection
 | |  |  | |
 | |  |  | ---------- Contact type code | P: Pin
 | |  |  | | S: Socket
 | | | |
 | | | -------------- Number of contacts
 | | |
 | | ----------------- Shell size code
 | |
 | -------------------- Delivery code | A: without contact
 | | no code: with contacts
 |
 --------------------------- Standard P/N

 

 B. P/N characteristics
 (1) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is +125 deg.C (+257.00 deg.F).
 (2) Contact arrangement R (Ref. Fig. 005)
 C. Connection procedure For connection procedure (Ref. Connection Table paragraph)

20-44-19 Page 9

 Miscellaneous Circular Connectors - Contact Arrangement NSA938018 and NSA938019 R Figure 005

20-44-19 Page 10

 _________________5. Plug 000100-0113C
 A. P/N Characteristics
 (1) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is +125 deg.C (+257.00 deg.F).
 (2) Contact Arrangement R (Ref. Fig. 006)
 B. Connection Procedure
 (1)
 Remove backshell ferrule and sealing grommet from connector.

 (2)
 To connect a new wire:

 -use crimp tool P/N 000407-0001 (BUCHANAN) or P/N 000407-0111 (DAVO)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(35)